Parameter / piece
Value / description
Torque
6 Nm
Turning angle
90
O
Turning time by 90
O
ARM 323: 60 s
ARM 343: 120 s
Control signal / power supply
3-point / 230 V AC
Working temperature
0-50
O
C
Power consumption
2,5-4 VA
Safety class
II
Protection class
IP42
Dimensions (H x W x D)
85,5 x 97 x 99 mm
Housing
PC
Cable length
2 m with plug
USING THE ARM ProClick ACTUATOR
MOUNTING ON AN FIRST GENERATION ARV VALVE OR OTHER PRODUCER’S
VALVES
1. Mode pushbutton
One must push the button to change from automatic to manual mode.
The mode pushbutton in the upper positon indicates automatic mode. When it is pushed down, one
can operate the actuator manually via the knob.
2. Signalling LEDs
The LEDs on the left and right inform about the turning direction of the actuator and valve. The left
one indicates turning counter-clockwise and the right clockwise. The shine also when the actuator is in
an end position but the controller still supplies power to the actuator. Observing the LEDs provides fast
diagnosis after finishing the assembly.
3. Position of the knob with scale
After mounting the actuator on the mixing valve and correctly choosing the scale, position “0” should
mean a valve fully closed (hot water closed) and position “10” a fully open valve (hot water open).
Every other position will indicate a percentage of opening, e.g. position “4” means that the valve is
open in 40%.
4. Taking the actuator off the valve
To take off the actuator from the valve, press the pushbutton of the
ProClick
mechanism (
1
) and slide
the actuator from the valve (
2
).
TECHNICAL DATA
MAINTENANCE
DECLARATIONS AND STATEMENTS
DISMOUNTING, DISPOSAL
WARRANTY
CUSTOMER SATISFACTION
The
ARM ProClick
valve is factory set on 50% (position “5” on the scale). To mount the actuator pro-
perly on the valve, the valve must also be set on 50%.
Full list of mounting sets for first generation of
ARV
valves
and other producer’s valves is to be found in the technical
price catalogue on
www.afriso.pl
.
1. Take off all the plastic parts from the valve, that will not be used.
2. Set the valve on 50%, so that the sleeve inside a 3-way valve will be right in the middle between
the hot and cold inlets (
Drawing 5
) or just in the middle of the outlet connections in a 4-way valve
(
Drawing 6
).
3. Place the adapter on the stem of the valve and screw it down. Screw the two counter screws into the
valve (
Drawing 13
). In first generation of
AFRISO ARV
valves (and most of other producer’s valves),
the triangle on the adapter is in the same position as the flattening on the stem and indicates the
sleeve position inside the valve. To screw in the counter screws into first generation of
AFRISO ARV
valves, sizes DN40 and DN50, one must unscrew the tightening Allen screws first (
Drawing 14
).
4. Slide the actuator on the valve, so that the 2 counter pins fit inside the appropriate holes in the back
of the actuator and the mechanism locks itself on them. The construction of the actuator allows
to mount it in different positions (
Drawing 8
). The blue ring with indicator must point upwards.
If it does not, one should pull off the knob and blue ring. Then mount it back with the indicator
pointing upwards.
5. Insert the double-sided scale in the correct position according to the opening/closing direction
(“from 0 to 10” or “from 10 to 0) (
Drawing 9
). The blue indicator should point at “5” on the scale.
If not, please return to point 2.
6. Connect the actuator to the controller according to the scheme (
Drawing 10
). The electric cable
of the actuator can be detached. This makes mounting and electrical connections easier. To take
out the plug, one must lift the lever of the cover and slide it out (
Drawing 11
). Next detach the plug
(
Drawing 12
). The plug fits into the socket only in one position.
3-way
4-way
Drawing 13. Mounting the
ARM ProClick
actuator on an
ARV
valve
Drawing 17. Dismounting the
ARM ProClick
actuator
Drawing 15. Mode pushbutton
Drawing 16. LEDs
Drawing 14.
ARV
DN40-DN50 valve
ProClick system disconnecting pushbutton
double-sided scale
knob with a thicker part showing
ring with indicator
mounting set (Art. No. 14 101 10)
f rst generation
ARV valve
ARM ProClick actuator
The
ARM ProClick
actuator is a maintenance-free product.
Electric actuators
ARM
are produced according to the directives of the European Union regarding: low-
-voltage equipment LVD (2014/35/EU), electromagnetic compatibility EMC (2014/30/EU), restricting
the use of hazardous substances RoHS (2011/65/EU). Electric actuators
ARM
comply also with the follo-
wing standards: EN 60730-1, EN 60730-2-14.
The manufacturer’s warranty for this product is 36 months after the date of sale from
AFRISO sp. z o.o.. In case of any alteration in the product or usage against this instruction manual,
the warranty becomes void.
For AFRISO sp. z o.o. customer satisfaction is the prime objective. Please contact us if you have any
questions, suggestions or problems concerning our product:
,
+48 32 330 33 55
.
1. Disconnect the power supply.
2. Dismount the device.
3. To protect the environment, this product must not be disposed of together with regular household
waste. Dispose of the product according to local directives and guidelines.
This device consists of materials that can be reused by recycling companies.
5
6
8
7
