aFe Power F2-03013 Instruction Manual Download Page 12

Warranty

General Terms:

• aFe warrants their products to be free from manufacturer’s defects due to workmanship and material.
• This warranty applies only to the original purchaser of the product and is non-transferrable.
• Proof of purchase of the aFe product is required for all warranty claims.
• Warranty is valid provided aFe instructions for installation and/or cleaning were properly followed.
• Proper maintenance with regular inspections of product is required to insure warranty coverage.
• Damage due to improper installation, abuse, unauthorized repair or alteration is not warranted.
• Incidental or consequential damages or cost, including installation and removal of part, incurred due to failure of aFe

product is not covered under this warranty.

• All warranty is limited to the repair and/or replacement of the aFe part.  To request Return Goods Authorization

(“RGA”).  Upon receipt of the RGA, you must return the product

 

to the address provided in the RGA, freight prepaid 

and accompanied with a dated proof of purchase and the RGA.

 

Upon receipt of the defective product and upon 

verification of proof of purchase, aFe will either repair or replace the

 

defective product within a reasonable time, not 

to exceed thirty days.

Product Category 

P/N Prefix  

Warranty duration

 

Direct OE Replacement Filters 

10, 11, 30, 31, 71, 73 

Life of the vehicle

Racing Filters 

18 

1 year 

Universal 

21, 24, 72 

2 years

Air Intake Systems 

50, 51, 54, 55, 75 

2 years

Exhaust Systems 

49 

2 years

Intercoolers & Intercooler Tubes 

46-2 

2 years

Intake Manifolds 

46-1 

2 years

Differential Cover/Transmission Pan 

46-7 

Life of the vehicle

Exhaust Manifolds 

46 

2 years

Throttle Body Spacers 

46-3 

2 years

Fluid Filters 

44 

90 days

Pre-Filters 

28 

2 years

Heavy Duty OE Replacement 

70 

2 years

PowerSports OE Replacement 

81, 87 

2 years

PowerSports Intake Systems 

85 

2 years

No other warranty expressed or implied applies nor is any person or advanced FLOW engineering authorized to assume 
any other warranty. Some States do not allow the exclusion or limitation of incidental or consequential damages or do 
not allow limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. 
This warranty gives you specific legal rights, and you may also have other rights which vary from State to State. 

Get top quality aFe products on our website.     We offer performance air intake systems that are tested to the limit and beyond. 

Summary of Contents for F2-03013













Reviews: