Aethlabs microAeth MA200 Operating Manual Download Page 9

16 

 

microAeth

®

 MA Series MA200, MA300, MA350 

Operating Manual

microAeth

®

 MA Series MA200, MA300, MA350 

Operating Manual                  

  17

AethLabs

AethLabs

2.2.11. Shipping

The microAeth MA series instruments contain lithium-ion batteries and therefore must be packaged and 
shipped properly according to regulations for different shipping methods. Please refer to International 
Air Transport Association (IATA) regulations when shipping the microAeth as there are limits to how many 
microAeth can be shipped in a single box based on the battery size in each instrument. The microAeth 
MA200 contains a 3.6V, 3200mAh (11.52 Wh), 1 cell rechargeable lithium-ion battery. The microAeth MA300 
contains a 3.6V, 12800mAh (46.08 Wh), 4 cell rechargeable lithium-ion battery. The microAeth MA350 
contains a 3.6V, 12800mAh (46.08 Wh), 4 cell rechargeable lithium-ion battery. Please contact your shipping 
carrier for more information and for packing instructions.

2.3. Warranty

If product(s) were not purchased directly from AethLabs. please check with your reseller for Warranty details.

Disclaimer of Warranties; Limitation of Liability. Seller warrants that the Products sold hereunder, under normal 
use and service as described in the operator’s manual, shall be free from defects in workmanship and material 
for the lesser of (i) twelve (12) months, or (ii) the length of time specified in the operator’s manual, from the 
date of the shipment to the Buyer (“Warranty Period”). This Warranty Period is inclusive of any statutory 
warranty. Notwithstanding the foregoing, this limited warranty is subject to the following exclusions and 
exceptions: (i) air pumps are warranted only for ninety (90) days unless otherwise specified in the operator’s 
manuals; (ii) parts repaired or replaced as a result of repair services are warranted to be free from defects in 
workmanship and material, under normal use, for the later of (a) ninety (90) days from the date of shipment 
to the Buyer, or (b) the end of the Warranty Period; (iii) Seller does not provide any warranty on finished 
goods manufactured by others or on other consumable materials; and (iv) unless specifically authorized by 
separate writing by Seller, Seller makes no warranty with respect to, and shall have no liability in connection 
with, goods which are incorporated into other products or equipment, or which are modified by any person 
other than Seller. Seller agrees during the Warranty Period, to repair or replace, at Seller’s option, defective 
Products so as to cause the same to operate in substantial conformance with the published specifications 
thereof; provided that Buyer shall (i) promptly notify Seller in writing upon the discovery of any defect, which 
notice shall be provided during the Warranty Period and shall include the product model and serial number (if 
applicable) and details of the warranty claim, and (ii) prepay the shipment costs. Replacement parts may be 
new or refurbished, at the election of Seller. All replaced parts shall become the property of Seller. Shipment 
to customer of repaired or replacement Products shall be made in accordance with the delivery provisions set 
forth in these Terms. In no event shall Seller have any obligation to make repairs, replacements or corrections 
required, in whole or in part, as the result of: (i) normal wear and tear; (ii) accident, disaster or event of force 
majeure; (iii) misuse, fault or negligence of or by Buyer; (iv) use of the Products in a manner for which they 
were not designed; (v) causes external to the Products such as, but not limited to, water damage, impact 
damage from fall, power failure or electrical power surges, lack of maintenance; (vi) improper storage and 
handling of the Products; or (vii) use of the Products in combination with equipment or software not supplied 
by Seller. If Seller determines that Products for which Buyer has requested warranty services are not covered 
by the warranty hereunder, Buyer shall pay or reimburse Seller for all costs of investigating and responding 
to such request at Seller’s then prevailing time and materials rates. If Seller provides repair services or 
replacement parts that are not covered by this warranty, Buyer shall pay Seller therefore at Seller’s then 
prevailing time and materials rates. ANY INSTALLATION, MAINTENANCE, REPAIR, SERVICE, RELOCATION 
OR ALTERATION TO OR OF, OR OTHER TAMPERING WITH, THE PRODUCTS PERFORMED BY ANY 
PERSON OR ENTITY OTHER THAN SELLER WITHOUT SELLER S PRIOR WRITTEN APPROVAL, OR ANY 
USE OF REPLACEMENT PARTS NOT SUPPLIED BY SELLER, SHALL IMMEDIATELY VOID AND CANCEL 

ALL WARRANTIES WITH RESPECT TO THE AFFECTED PRODUCTS. THE OBLIGATIONS CREATED BY 
THIS WARRANTY STATEMENT TO REPAIR OR REPLACE A DEFECTIVE PRODUCT SHALL BE THE SOLE 
REMEDY OF BUYER IN THE EVENT OF A DEFECTIVE PRODUCT OR OTHERWISE FOR BREACH OF THIS 
WARRANTY OR THESE TERMS. EXCEPT AS EXPRESSLY PROVIDED IN THIS WARRANTY STATEMENT, 
SELLER DISCLAIMS ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, ORAL OR WRITTEN, 
WITH RESPECT TO THE PRODUCTS, INCLUDING WITHOUT LIMITATION ALL IMPLIED WARRANTIES OF 
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. SELLER DOES NOT WARRANT THAT 
THE PRODUCTS ARE ERROR-FREE OR WILL ACCOMPLISH ANY PARTICULAR RESULT. SELLER MAKES 
NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, REGARDING THE 
PRODUCTS, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTIES OF MERCHANTABILITY OR FITNESS 
FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL SELLER BE LIABLE FOR COSTS OF PROCUREMENT 
OF SUBSTITUTE GOODS AND SERVICES, LOSS OF USE OR LOST PROFITS, OR ANY OTHER SPECIAL, 
INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES, ARISING OUT OF OR RELATED TO ANY SALE 
OF THE PRODUCTS OR THE USE OR PERFORMANCE OF THE PRODUCTS, HOWEVER CAUSED AND 
ON ANY THEORY OF LIABILITY, WHETHER IN AN ACTION FOR CONTRACT, TORT OR OTHERWISE, AND 
WHETHER OR NOT SELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

2.4. End User License Agreement (EULA)

READ THIS END USER LICENSE AGREEMENT (“AGREEMENT”) CAREFULLY BEFORE USING THE 
ACCOMPANYING SOFTWARE AND ANY ASSOCIATED FIRMWARE (COLLECTIVELY, THE “SOFTWARE”). 
BY DOWNLOADING AND USING THE SOFTWARE, YOU ACKNOWLEDGE THAT YOU HAVE READ THIS 
AGREEMENT, THAT YOU UNDERSTAND IT, AND THAT YOU ACCEPT AND AGREE TO BE BOUND BY ITS 
TERMS. IF YOU ARE NOT WILLING TO BE BOUND BY THE TERMS OF THIS AGREEMENT, YOU SHOULD 
TERMINATE THE DOWNLOAD AND/OR INSTALLATION PROCESS, AND REFRAIN FROM ACCESSING OR 
USING THE SOFTWARE.

THE SOFTWARE IS COPYRIGHTED AND IS LICENSED TO YOU UNDER THIS AGREEMENT; IT IS NOT 
SOLD TO YOU. THIS AGREEMENT REPRESENTS THE ENTIRE AGREEMENT BETWEEN YOU AND 
MICROAETH CORPORATION DBA AETHLABS CONCERNING THE SOFTWARE, AND THIS AGREEMENT 
SUPERSEDES AND REPLACES ANY PRIOR PROPOSAL, REPRESENTATION, OR UNDERSTANDING YOU 
MAY HAVE HAD WITH AETHLABS RELATING TO THE SOFTWARE.

License Grant. microAeth Corporation DBA AethLabs (“Licensor”) hereby grants you a personal, non-
transferable and non-exclusive license to use (i) the Software, and (ii) any related documentation or electronic 
instructions accompanying the Software (the “Documentation”).

You obtain no right, title or ownership in any Software or Documentation, nor do you obtain any right to 
sublicense the Software. The Software may be used only as provided in either machine-readable object code 
form or machine-compressed form. This license is not a sale of the original or any copy of the Software. 
You may use the Documentation to assist in your use of the Software, but you may not make copies of the 
Documentation.
Use Restrictions. Except to the extent these restrictions are prohibited by applicable law or prohibited by 
the terms of any Open Source License, you must not, and must not allow any other person to: (a) use the 
Software to conduct comparative or competitive analyses, including benchmarking; (b) reverse engineer, 
decompile, reverse compile, reduce in human readable form or otherwise access the source code of the 
Software; (c) sublicense, rent, lease, modify, enhance, supplement, create derivative works from the Software; 

Summary of Contents for microAeth MA200














































Reviews: