manualshive.com logo in svg

AES i-Gate 100, Installation Manual

Share
Download
AES i-Gate 100 Installation Manual Download Page 10

V1 

Page 10 

 

10. Using the device as a Gate / Door Opener 

 

 
 
 
 
 

 
 

 
 
 

 

  

     

    

   

 

 

11. Using the APP

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

The user can call the SIM number of the 
intercom from their phone. If their number is 
stored then the device will hand up the call 
without answering and trigger the gates or 
door with a momentary trigger. 
 
The user can also send the following SMS text 
messages to further control the unit.. 
 
 

 

 

Press to trigger gates. 
 

For gates set for automatic 
closing, press to hold open 
 

More buttons.. 

-Check gate status 
-Check signal strength 
-Check stored numbers 
 

For gates set for automatic 
closing, press to allow the 
gates to close again. 
 

Information 
 

The App is available for Android 
and Iphone devices called  

GSM-Gate

. 

 
Note: Before the app can be used, 
the sim card number and SMS text 
strings will needed entered in the 
settings screen. 
 
The default SMS strings are shown 
in the settings page for your 
convenience. 
 

Summary of Contents for i-Gate 100















Reviews:

No comments

Brands by name

Popular brands

Load more brands