Handsets will be
displayed in
order of H1, H2,
H3 & H4.
ON/OFF
RECEPTION
INDICATOR
BATTERY
LEVEL
RED PAIRING
LED
CODE BUTTON
OK
OK
MONITORING
GATE/DOOR
TRIGGER
VIBRATE
ON/OFF
OK
OK
1. Brightness
2. Language
3. Messages
4. Bell
5. Colour
Access menu by holding monitoring
button for 3 seconds
1. Adjusts brightness.
2. English, French or German.
3. Listen or delete Voicemail.
4. Change the ring tone.
5. Change screen colour.
RE-CODING/ADDING EXTRA HANDSETS
INFORMATION ABOUT YOUR DECT HANDSET
The handset should ideally be charged for at least 8 hours before use. It is recommended to give it at least 60 minutes of charge
before performing the range test between the transmitter module and the handset inside.
If re-pairing the video handset it must be the first device paired to receive both video & audio channels.
* ALWAYS RANGE TEST THE UNIT ON SITE BEFORE INSTALLATION *
Occasionally the system may need to be re-coded once installed.
If the handset does not ring when the call button is pressed,
the system may need to be re-coded.
(
● =
FULL RE-CODE : STEP 1-5 )
(
● =
ADDING A HANDSET : STEP 3-5 )
●
Step 1)
Press and hold the
CODE BUTTON
inside on the Transmitter PCB for 5 seconds
until the audible tone is heard from the Intercom speaker.
●
Step 2)
Then press the
CODE BUTTON
14 times
and proceed to wait until the melody is
heard or the LED turns off. Performing this step will remove
ALL
handsets currently synced
(or partially synced)
to the system.
●
●
Step 3)
Press and hold the
CODE BUTTON
inside on the Transmitter PCB for 5 seconds
until the audible tone is heard from the Intercom.
●
●
Step 4)
Then press and hold the
CODE BUTTON
on the handset until the red LED at the
top begins to flash. After a few seconds you will hear a melody play to let you know it has
successfully connected.
●
●
Step 5)
Finally you should test the kit to ensure that everything is working as expected
by pressing the Call Button on the CallPoint to ensure the handset and/or wall mounted unit
receives the call and that the two way speech is functioning correctly.
8.000
TRANSMITTER
CODE BUTTON
Example shows the
location of the CODE
BUTTON that can be found
on the back of the wall
mounted unit.
CODE BUTTON
Can be found on
reverse side.
OK
OK
AC/DC STRIKE LOCK
WIRING EXAMPLE
Follow this method when using a Strike Lock with
the system. If used it will mean that if a relay in
either the Transmitter or
optional AES Keypad
is
triggered it will temporarily allow the door/gate
to release.
MAINS
POWER
Do you require a custom wiring diagram for your site? Please send all
requests to
and we will do our best to
provide you with a supplement diagram suitable for your chosen
equipment.
We are constantly using your customer feedback to enhance all of our
guides / learning material for installers.
If you have any suggestions regarding this please send any
suggestions to
1. When the intercom is being called, identify the visitor on the screen.
2. Press the OK button to answer the incoming call.
3. Speak clearly into the top of the handset at a distance of 10-20cm.
4. During the call press < or > to increase or decrease the volume.
5. Press the button to release the door/gate and press OK to end the call.
CHANGING
SETTINGS
Note : The video will remain active for 1 minute after the audio call has ended.
The following settings can be
changed on the handset at any
time.
Use up and down arrows to
navigate, press OK to select. Press
right arrow at any time to exit or
cancel change.
( HANDSET BATTERY INCLUDED )
705 DECT
- Radio Intercom System
STILL HAVING TROUBLE?
Find all of our support options such as Web Chat,
Full Manuals, Customer Helpline and more on
our website:
WWW
.
AESGLOBALONLINE
.
COM
( Note: Doing this step will also clear ALL voicemails after reset. )
( Repeat Steps 3 & 4 for each new handset. )
( Video Handsets must be added first and 1 MAX )
N/ C
| C |
N/ O
N/ C
| C |
N/ O
STRIKE
LOCK
MAX 24 VOLTS!
POWER ADAPTER
+
-
TRANSMITTER
AES KEYPAD
* STRIKE LOCK PSU SOLD SEPARATELY *
MICROPHONE
