background image

TUBÒ ROBÒ TR900L Instruction Manual

EN

EN

77

CHARGING THE BATTERY

FIRST ROBÒ CHARGE

LOW BATTERY LEVEL

TOTAL CHARGING TIME

When charging TUBÒ ROBÒ for the first time, 
place it on the charging dock until the battery is 
fully charged.

FLASHING BLUE LIGHT

Charging in progress

STEADY BLUE LIGHT

Charging completed

STEADY RED LIGHT

Robot flat

 

WARNING

Leave TUBÒ ROBÒ to charge on the charging 

dock until the flashing blue light turns off.

STAND-BY

BATTERY REPLACEMENT

Once TUBÒ ROBÒ has been fully charged, it enters the 
STAND-BY mode. 
To reactivate, press the button 

 for 1 second.

TIPS FOR USE

For improved cleaning efficiency, inspect the areas involved beforehand and prepare them as follows:
•  Before each use, fully charge the battery.
•  Orient the self-cleaning base preferably towards the center of the cleaning area.
•  Clear the surfaces of the home from any obstacles that can be struck during cleaning, move any objects lying in 
the way such as electrical cables, shoes, handbags with straps, magazines and newspapers, remove light rugs, vases 
and fragile furnishings, toys scattered on the floor, place chairs above the tables, raise curtains or sofa covers with 
fringes touching the floor, and lift bowls for pet food.
•  Be careful with objects in precarious balance that can be struck by the robot directly or indirectly. Check that 
any open doors are not closed after colliding with ROBÒ, blocking the latter inside the room and preventing it from 
returning to the charging dock.
•  ROBÒ performs its cleaning cycle regularly even if domestic animals are present. Any zones of the home to be 
excluded from ROBÒ’s path can be delimited using the FORBIDDEN ZONE function of the app. AERTECNICA DEVICE.

If the battery level is below 20%, TUBÒ ROBÒ will not be 
able to function.
In such case, it must be placed manually on the charging 
dock and left there until the battery charges fully.

If the battery is completely flat, it may take roughly 
2 hours to charge completely.

Lithium batteries constitute special 
solid waste that must be disposed of 
according to the applicable regulations.

If prolonged periods of non-use are expected, 
charge the battery fully, remove it and store it 
in a cool and dry place.

PLEASE NOTE

When the battery is exhausted, it must be replaced 
with a new original one. The instructions for replacing 
the battery are included in the spare part’s package.

AVOID

RECOMMENDED

ANTI-FALL SENSORS

TR900L will return to the charging base automatically 
if the battery level il less than 20% in use and will be 
powered off. It restart cleaning automatically from 
where left off until the job was completed.

AUTOMATIC CHARGING - RESTART CLEANING

Upgrade firmware: If new firmware is detected, 

upgrade it according to prompt. The battery level 

should be 

 al 50% during firmaware upgrade

TUBÒ ROBÒ is equipped with anti-fall sensors to stop it in presence of stairs (balconies, middle floor, etc…)
However, if the accidental fall of the robot can cause damage to things or people, it is highly recommended to 
increase safety by inserting 

FORBIDDEN ZONES

 with AERTECNICA DEVICE app.

FORBIDDEN ZONE
Use AERTECNICA DEVICE 
app to exclude
areas of the house
from cleaning.

FORBIDDEN 

ZONE

FORBIDDEN 

ZONE

FORBIDDEN 

ZONE

Summary of Contents for TUBO ROBO TR900L

















Reviews: