background image

Installation and Operation

To decrease the risk of damage to the equipment, you must obey the precautions that follow.

DANGER: General Hazard Warning!

This product can produce high forces and move at velocities that could cause injury.
The user is responsible for its safe operation. The following general equation is
provided to assist with risk assessments in regards to contact and pinch points:

WARNING: General Hazard Warning!

l

Only trained operators should operate this equipment.

l

All service and maintenance must be done by approved personnel.

l

Use this product only in environments and operating conditions that are approved in
this manual.

l

Never install or operate equipment that appears to be damaged.

l

Make sure that the product is securely mounted before you operate it.

l

Use care when you move the ANT130LZ or you could negatively affect the per-
formance of it.

WARNING

:

Trip Hazard!

Route, house, and secure all cables, duct work, air, or water lines. Failure to do so could
introduce trip hazards around the system that could result in physical injury or could
damage the equipment.

Hardware Manual

ANT130LZ

www.aerotech.com

9

Summary of Contents for ANT130LZ Series





















































Reviews: