manualshive.com logo in svg

Aeroqual AQM 65, User Manual, Page: 89 / 127

Share
Download
Aeroqual AQM 65 User Manual Download Page 89

 

 

MRK-D-0034 V2.0 

 

 

 Aeroqual AQM 65 User Guide  

 

 

Page | 88 

 

AQM 65 gas module 

O3 

NO2 

NOx 

CO 

SO2 

VOC 

H2S 

CO2 

Gas used for 

calibration 

O3 

NO2 

NO2 or NO 

CO 

SO2 

Isobutylene 

C

4

H

8

 

H2S 

CO2 

Gas module 

measurement range 

0 to 0.5 

ppm 

0 to 0.2 ppm  0 to 0.5 ppm  0 to 25 ppm 

0 to 10.0 

ppm 

0 to 20 ppm 

0 to 10 

ppm 

0 to 2000 

ppm 

(0.2 %) 

Span gas 

concentration for 

calibration  

Recommended  

Minimum, Maximum

 

0.1 ppm 

 

0.08  -

0.150

 

0.1 ppm 

 

0.05 - 0.150

 

0.1 ppm 

 

0.05 - 0.2

 

10.0 ppm 

 

5 - 15 

 

0.5 ppm 

 

0.2 

– 1.5

 

10.0 ppm 

 

5 - 15

 

0.5 ppm 

 

0.2 

– 1.5

 

1000 ppm 

Recommended 

cylinder 

concentration when 

using AirCal 1000 or 

AirCal 8000 

Recommended (ppm) 

Minimum, Maximum

 

Ozone is 

delivered 

by an 

Ozone 

generator  

20 ppm 

 

10 - 100

 

20 ppm 

 

10 - 100

 

1000 ppm 

 

500 - 5000

 

20 ppm 

 

10 - 100

 

1000 ppm 

 

500 - 5000

 

20 ppm 

 

10 - 100

 

1000 ppm 

 

500 - 1500

 

Recommended Gas 

cylinder from 

www.calgaz.com

 

 

Part number: 

N/A 

20 ppm NO2 

Balance AIR 
8AL 58 liters 

C10 fitting 

 

A0446046 

 

20 ppm NO2 

Balance AIR 
8AL 58 liters 

C10 fitting 

 

A0446046 

 

1000 ppm CO 

Balance N2 

6D 103 liters 

C10 fitting 

 

A0436734

 

20 ppm SO2 

Balance N2  

8AL 58 litres 

C10 fitting 

 

A0446071  

Isobutylene 

1000 ppm 

Balance Air 6D 

103 litres 

 

A0436843 

 

20 ppm H2S 

Balance N2  

8AL 58 litres 

C10 fitting 

 

A0446004

 

1000 ppm 

CO2 Balance 

Air 

6D 103 litres 

C10 fitting 

 

A0189932

 

Table 5-1 Recommended calibration cylinder concentrations. The recommended concentration is written 
in 

bold, 

the minimum and maximum recommend concentration are written in 

green

 in the table. 

5.2.2  Cylinder of certified zero air and certified CO2 for CO2 calibration 

CO2 cannot be calibrated using the Aeroqual calibration systems, a cylinder of certified zero air, 
Calgaz part number 

A0194363

 should be used to zero calibrate the CO2 module. And a cylinder of 

1000 ppm CO2 part number 

A0189932

 used to span calibrate the CO2 module. See Appendix 4 for 

detail on CO2 calibration. 

 

 

5.2.3  Considerations for gas cylinder size  

Any gas cylinder size can be used with the Aeroqual AirCal systems, Figure 5-1 shows a range of 
cylinder sizes which can be used successfully with the AirCal 1000. Any of the cylinders in Figure 5-1 
can also be used successfully with the AirCal 8000, however the AirCal 8000 cylinder enclosure is 
designed to hold the 6D and 8AL cylinders from Calgaz,, Figure 5-5, therefore larger cylinders will 
need to be secured and protected if they are to be used with the AirCal 8000. 

 

Online 

reference 

training.aeroqual.com AQM 65 Technical Training Section 5

 

 

Online video 

https://vimeo.com/152956203

  

https://vimeo.com/152913736

 

 

Larger cylinders will be difficult to transport; small gas cylinders are easier to store and transport. 

Summary of Contents for AQM 65
































































































































Reviews:

No comments