Aeroqual AQM 65 User Manual Download Page 76 | Manualshive

Page: 76 / 127

Aeroqual AQM 65 User Manual Download Page 76

MRK-D-0034 V2.0

Aeroqual AQM 65 User Guide

Page | 75

4.4.12.4 Check TMS compressor gas pressure and re-fill

The coolant in the TMS compressor gas is R134a (1,1,1,2-Tetrafluoroethane). This is a common
refrigerant gas. The gas must be purchased locally because Aeroqual cannot ship gas.

Aeroqual can provide the pressure gauge to measure the compressor pressure, see Figure 4-28.

IMPORTANT!

The compressor requires that gas be added to a specific PRESSUE, not a specific weight, so it is
very important to use the pressure gauge provided by Aeroqual when re-filling the compressor
with gas.

Figure 4-28 The pressure gauge provided by Aeroqual for refilling the compressor with gas

You will also need a valve to add to the can or cylinder of gas.

Aeroqual can provide a charging hose (AQM R12) to connect the valve to the pressure gauge.

Figure 4-29 Parts required for refilling the TMS compressor with coolant gas. The gas and valve must be
purchased locally

NOTE:

The TMS compressor will require between 8 and 10 grams of gas for a full refill

«
...
74
75
76
77
78
...
»

Summary of Contents for AQM 65
































































































































Reviews:

No comments