manualshive.com logo in svg

Aeroqual AQM 65, User Manual, Page: 74 / 127

Share
Download
Aeroqual AQM 65 User Manual Download Page 74

 

 

MRK-D-0034 V2.0 

 

 

 Aeroqual AQM 65 User Guide  

 

 

Page | 73 

4.4.12.3  Clean TMS cassette and condenser fins 

Dirt and other debris can accumulate in the compressor cassette and can affect air flow through the 
cassette and lead to overheating of the compressor. Keeping the compressor clean is an important 
part of thermal management system maintenance.  

AQM 65s which are installed in environments with high amounts of airborne dirt and dust will require 
more frequent cleaning. 

Figure 4-25 shows how dust and debris can accumulate within the TMS cassette  

 

 

Figure 4-25 Dirt and debris can accumulate within the TMS cassette leading to reduced efficiency of the 
thermal management system. 

Use a damp cloth to wipe the compressor tank and copper lines. 

Use a small long handled brush to gently clean the condenser fins from top to bottom in short 
downward strokes parallel to the fins. 

Do not brush against the fins as this can cause the fins to bend out of shape. 

 

Figure 4-26 Clean the condenser fins by brushing up and down parallel to the direction of the fins 

 

 

Summary of Contents for AQM 65
































































































































Reviews:

No comments