manualshive.com logo in svg

Aeroqual AQM 65, User Manual, Page: 69 / 127

Share
Download
Aeroqual AQM 65 User Manual Download Page 69

 

 

MRK-D-0034 V2.0 

 

 

 Aeroqual AQM 65 User Guide  

 

 

Page | 68 

4.4.11 Add, remove or replace a gas module 

Changing the module configuration can be done easily on site at the monitoring location. Module 
replacement can be done with the AQM 65 power on. 

A change in the module configuration will result in a change of inlet flow rate. It is important to 
measure the inlet flow rate after the module change and document this in the instrument journal. 

 

 

Tools required 

Tube Cutter, Large Phillips head screw driver, AQM R7 

 

Parts required 

Tubing: CS Tube10 CS Tube11, power cable, communication cable, 
2x luer cap 

 

Frequency of 

service 

As required 

 

Online 

reference 

training.aeroqual.com

: AQM 65 technical Training Section 5.2 

 

Online video 

Add a module

        

https://vimeo.com/161433950

  

Remove a module 

https://vimeo.com/161399843

  

 

If a module is removed or added then a software change is required. The software module 
configuration can be found in the configure instrument app. Sensor modules can be added or 
removed using this tool, shown in Figure 4-21. 

 

 

Figure 4-21 Change the module configuration in the software in the configure instrument app 

 

 

Summary of Contents for AQM 65
































































































































Reviews:

No comments