manualshive.com logo in svg

Aeroqual AQM 65, User Manual, Page: 53 / 127

Share
Download
Aeroqual AQM 65 User Manual Download Page 53

 

 

MRK-D-0034 V2.0 

 

 

 Aeroqual AQM 65 User Guide  

 

 

Page | 52 

4.4.2  Replace gas sample inlet filter 

The gas inlet filter is held inside the enclosure at the top left. This must be changed to ensure 
accurate readings, the filter is disposable and can be thrown away.  

The filter should be changed when it becomes dirty as shown in Figure 4-4. The frequency of filer 
changes depends upon local environmental conditions. 

 

Tools required 

None 

 

Parts required 

AQM R12 (bag of 25 filters) 

 

Frequency of 

service 

Recommended 

Monthly

 (depends on local conditions) 

See Section 4.6 for further discussion on filter change frequencies. 

 

Online 

reference 

training.aeroqual.com

: AQM 65 technical Training Section 4.1 

 

Online video 

https://vimeo.com/119923276

 checked

 

 

Do not turn off the AQM 65; this procedure can be done with the AQM 65 turned on.  

 

NOTE: 

It is very important to check the AQM 65 inlet flow rate is correct after changing the filter to 
ensure there are no leaks. 

 

 

 

Figure 4-4 The particle filter on the gas inlet can be easily replaced, it should be replaced when it gets 
dirty as shown in the image on the right. (a new filter is shown on the left, dirty filter on the right) 

 

 

Summary of Contents for AQM 65
































































































































Reviews:

No comments