Aeropro LT50 Operating Instructions Manual Download Page 7

Air Finish nailer LT50             

        Http://www.aeroprotools.com 

 

4. Preparing the tool for use 

4.1 Preparing a tool for first time operation 

Please  Read  and  observe  these  Operating  Instruction  before  using  the  tool.  Basic  safety  measures 

should always be strictly followed to protect against damage to the equipment and personal injury to the 

user or other people working in the vicinity of operation. 

 

4.2 Connection to the compressed air system 

Ensure  that  the  pressure  supplied  by  the  compressed  air  system  does  not  exceed  the  maximum 

allowable  pressure  of  the  fastener  driving  tool.  Set  the  air  pressure  initially  to  the  lower  value  of  the 

recommended allowable pressure (see

 

TECHNICAL DATA). 

Empty the magazine to prevent a fastener from being ejected at the next stage of work in the event that 

internal parts of the fastener driving tool are not in the starting position following maintenance and repair 

work or transportation. 

Connect the fastener  driving tool  to the compressed air supply  using suitable pressure hose  equipped 

with quick-action connectors. 

Check for  proper  functioning  by  applying  the  muzzle  of  the  fastener  driving  tool  to a  piece  of  wood  or 

wooden material and actuating the trigger once or twice. 

 

4.3Filling the magazine 

Only those fasteners specified under TECHNICAL DATA (see 1.1) may be used 

When filling the magazine, hold the tool so that the muzzle is not pointing towards the operator or any 

other person or animals. 

4.4 Handling the tool 

Pay attention to 

2-Special Reference-

of these operating instructions. 

Having checked that the fastener driving tool is functioning correctly, apply the tool to a work piece and 

actuate the trigger. 

Check whether the fastener has been driven into the work piece in accordance with the requirements. 

-  if  the  fastener  is  protruding,  increase  the  air  pressure  in  increments  of  0.5  bar,  checking  the 

result after each new adjustment; 

- if the fastener is driven into an excessive depth reduce the air pressure I increments of 0.5 bar 

until the result is satisfactory. 

You should endeavor in any event to work with the lowest possible air pressure. This will give you three 

significant advantages; 

          1. Energy will be saved, 

          2. Less noise will be produced, 

          3. A reduction in fastener driving tool wear will be achieved. 

Avoid triggering the fastener driving tool if the magazine is empty. 

Any defective or improperly functioning fastener driving tool must immediately be disconnected from the 

compressed air supply and passed to a specialist for inspection. 

In  the  event  of  longer  breaks  in  work  or  at  the  end  of  the  working  shift,  disconnect  the  tool  from  the 

compressed air supply and it is recommended to empty the magazine. 

The compressed air connectors of the fastener driving tool and the hoses should be protected against 

contamination, the ingress of coarse dust chips, sand etc, will result in leaks and damage to the fastener 

driving tool and the couplings. 

Summary of Contents for LT50











Reviews: