Use
The “Mode button” allows you to select the different operating modes:
Comfort, Economy, Frost protection, programming
AUTO
mode.
Pressing the
i
button gives you the temperature of the room
or the set-point
temperature, according to your configuration
settings in menu 5.
If the ON icon is displayed, this means that the device is in heating demand mode.
Time Setting
In Off mode, press the button.
The days flash.
Press the button once to access the
programming, and press the On/Off button
once to exit the setting mode.
Menu number
19,0
PROG
c
On-Off
Button
>10sec.
OK
1
2
3
4
5
6
7
3,5
c
OK
1
2
3
4
5
6
7
----
OK
1
2
3
4
5
6
7
0,0
c
OK
1
2
3
4
5
6
7
90
OK
1
2
3
4
5
6
7
0
OK
1
2
3
4
5
6
7
42
Instruction digital thermostat (ITRD)
Hours
Minutes
Day
On-Off
Button
OK
00:00
1
2
3
4
5
6
7
19,0
PROG
On-Off
Symbol off
c
Button
On-Off
Mode button
15,5
c
i
15,5
c
i
19,0
c
i
Configuration
When in Off mode, press and hold down the On/Off
button for 10 seconds to access the first configuration
menu.
If the Heater is in mode „Off”, the display shows
Digital control display
Menu 1:ECO set-point adjustment
By default, Economy setting = Comfort setting - 3.5°C. This
reduction can be set between 0 to -10°C, in steps of 0.5°C.
To adjust the reduction, press on the + or - buttons then press
OK to confirm and go to the next setting.
To allow the user to modify the set-point, press on the + button
in Economy mode until “----” is displayed on the screen.
Menu 2: Correction of the measured temperature
If there is a difference between the temperature noted
(thermometer) and the temperature measured
and displayed by the unit, menu 2 acts on the measurement
of the probe so as to compensate for this
difference (from -5°C to +5°C in steps of 0.1°C).
To modify, press on the + or - buttons then press
OK to confirm and go to the next setting.
Menu 3: Backlight time out setting
The time out can be adjusted between 0 and 225 seconds,
in steps of 15 seconds (set on 90 seconds by default).
To modify, press on the + or - buttons then
press OK to confirm and go to the next setting.
Menu 4: AUTO mode temperature display option
0 = Continuous display of room temperature.
1 = Continuous display of set-point
temperature.
To modify, press on the + or - buttons then
press OK to confirm and go to the next setting.
Menu 5: Product number
This menu allows you to view the product number.
To exit the configuration mode, press OK.
Programming
When starting up, the “Comfort mode from 8am to
10pm” program is applied to all the days of the week.
To change the programming, press the
PROG
button in
Off or AUTO mode. The 1st time slot flashes on and off.
no
“Frost protection”
stroke
Confirm and go to
the next day
Frost protection
mode for 1 hour
Day
OK
22 24
1
2
3
4
5
6
7
20
16 18
00:00
14
10 12
8
PROG
Economy mode for 1 hour
4
6
PROG
2
0h
Comfort
mode for 1 hour
Control display
two strokes
“Comfort”
one
“Economy”
stroke
Quick programming:
To apply the same program to the following day, press and hold the OK button for
approximately 3 seconds until the program of the following day is displayed. To exit
the programming mode, press on the On/Off button.
Continuous Comfort
Pressing and holding the + or - buttons lets you
change the
current set-point (+5 to
+30°C) in
steps of 0.5°C.
Continuous Economy mode
The Economy set-point is indexed according to the Comfort
set-point. The reduction can be modified in the configuration
settings for menu 1.
Modifying the Economy set-point
The set-point can be modified if it was authorized in the
configuration settings in menu 1 (“----”).
Pressing and holding the + or - buttons lets you change the
current set-point (+5 to +30°C) in steps of 0.5°C.
6
QUICK ACCESS see page 7!
