aero-naut 1128/03 Manual Download Page 25

Fit ribs TT-09 to TS-23 in place in numerical order. Glue in place aileron riblets TT-24 and TT-25. Make sure you position 
ribs exactly at right angles in relation to spar, then glue in place. Note, that ribs are glued to spruce spar, main spar, 
trailing edge sheeting and aileron sheeting. Do not apply glue to front part of ribs between wing spar and leading edge 
position.
Root rib TT-08 will be fitted at a later stage.

4

TT-09

TT-04

TT-04

TT-08

TT-08

TT-10

TT-11

TT-12

TT-13

TT-23

TT-22

TT-25

TT-24

Now glue in place TT-04 and 
root rib TT-08. 
Make sure root rib is slightly 
angled in accordance with 
dihedral of wing.

5

6

Cut to length upper spruce spar TT-02 (2 x 8 mm) and glue to ribs and main spar. Use suitable weigths to hold spar in place and leave to dry. 

TT-02

Glue in place aileron spar TT-26, aileron leading edge TT-27 as well as gussets 
TT-28 and TT-29. Insert servo tray TT-30 between ribs TT-14 and TT-15 flush 
with underside of ribs and against wing spar. Do not glue!
Glue end stop TT-30.1 to both ribs and glue reinforcement TT-30.2 in place on 
aileron.

7

Slightly bevel the last 3 mm of trailing edge and aileron sheeting to establish a good contact surface for gluing. Then glue in place top 
sheeting. Fit aileron top sheeting in place and achieve a good joint with leading edge TT-27.

Tip:

 Glue rear edge of sheeting with epoxy to get a strong trailing edge which can be sanded down to fine profile.

8

TT-30

TT-30.1

TT-30.2

TT-14

TT-26

TT-27

TT-28

TT-29

TT-15

Glue together servo frames TT-30.3 and TT-30.4 as shown, and glue to spar 
and ribs. Make sure that hole for servo lead is not obstructed.

Attention: Do not glue frame to servo tray TT-30!

 TS-32 is 

merely used to position frame correctly.

TT-30.3

TT-30.4

Summary of Contents for 1128/03









































Reviews: