AERMEC WRCB User Manual Download Page 23

Page: 23 / 24

ERRORS DISPLAY

If there is an error occurring during the operation of the system, the error code will be displayed on the LCD, as show in Fig. 24. If multi errors occur at the same time, their
codes will be displayed circularly.

Note: In event of any error, please turn off the unit and contact the professionally skilled personnel.

Fig. 24

Error

Error code

Error

Error code

Return air temperature sensor open/short circuited

Drive board communication error

Evaporator temperature sensor open/short circuited

Compressor overheating protection

Indoor unit liquid valve temperature sensor open/short circuited

Indoor and outdoor units unmatched

Indoor gas valve temperature sensor open/short circuited

Communication line misconnected or expansion valve error

IPM temperature sensor open/short circuited

Running mode conflict

Outdoor ambient temperature sensor open/short circuited

Pump-down

Outdoor unit condenser mid-tube temperature sensor open/short circuited

Defrost or oil return

Discharge temperature sensor open/short circuited

Forced defrosting

Communication error between indoor and outdoor unit

Compressor startup failure

DC bus under-voltage protection

High discharge temperature protection

DC bus over-voltage protection

Overload protection

Compressor phase current sensing circuit error

Whole unit over-current protection

Compressor demagnetization protection

Over phase current protection

PFC protection

Compressor desynch

IPM Temperature Protection

IPM Current protection

Overload protection

Compressorphaseloss/reversal protection

System charge shortage or blockage protection

Frequency restricted/reduced with whole unit current protection

Capacitor charging error

Frequency restricted/reduced with IPM current protection

High pressure protection

Frequency restricted/reduced with high discharge temperature

Low pressure protection

Frequency restricted/reduced with antifreezing protection

Compressor stalling

Frequency restricted/reduced with overload protection

Over-speeding

Frequency restricted/reduced with IPM temperature protection

Drive board temperature sensor error

Indoor unit full water error

AC contactor protection

Anti-freeze protection

Temperature drift protection

AC input voltage abnormal

Sensor connection protection

Whole unit current sensing circuit error

DC bus voltage drop error

4-way valve reversing error

Outdoor fan 1 error protection

Motor stalling

Outdoor fan 2 error protection

PG motor zero-crossing protection

Compressor suction temperature sensor error

Indoor fan tripping error

IDU network address error

Summary of Contents for WRCB

























Search results

Summary of Contents for WRCB

Reviews:

Brands by name

Popular brands

AERMEC WRCB, User Manual

Search results

Summary of Contents for WRCB

Reviews:

Brands by name

Popular brands