Aerial-51 SKY-SDR User Manual Download Page 23

23 

SKY-SDR USER MANUAL Ver. 1.3.1  -  28-MAR-2017 

21  Voice VOX Level 

Adjusts the VOX Gain (sensitivity) in SSB Mode from 

10 (most sensitive) to 100 (least sensitive).  For the 

original hand mic, use "80". 

22  Voice VOX 

(VOX DELAY) Select DISABLE (turns VOX OFF) or 
adjust delay from 100 ms to 5 sec. in steps of 100 

ms. 

23  Compress TX 

Adjusts TX Speech Processor from 1 (minimum 
compression) to 100 (maximum compression). 

Always set to 40 to 50% when used with the 

factory Hand-MIC.

  

24  Reverberator 

Adjust TX audio reveberation: Default: 'DISABLE'; 

Press RIT/XIT to toggle between 3 adjustments;  
Delay: '40ms', '80ms', or '160ms'; Depth: 1-7; 

Level: 1-7.  Change value by rotating VFO knob. 

25  EQ TX 

Adjusts TX Audio Equalizer in 3 ranges, 'LOW' 

Frequencies, 'MEDium' Frequencies, and 'HIGH' 

Frequencies in steps from 1 (deemphasize) to 10 
(maximum emphasis).  Toggle between the 3 ranges 

by pressing the RIT/XIT button on the front panel. 

RECOMMENDED:  LOW=10, MED=6, HIGH=6 

26  EQ RX 

Adjusts RX Audio Equalizer in 3 ranges, 'LOW' 

Frequencies, 'MEDium' Frequencies, and 'HIGH' 

Frequencies in steps from 1 (deemphasize) to 10 
(maximum emphasis).  Toggle between the 3 ranges 

by pressing the RIT/XIT button on the front panel. 

27  Pan Level 

Adjusts the 'Gain Level' of the Pan Adapter from 0 to 
30.  30 = 60dB. 

SOFTWARE MENU QUICK GUIDE 

 

Summary of Contents for SKY-SDR





























Reviews: