Aerco 5R5-384 User Manual Download | Manualshive

Page: 15 / 139

background image

AERCO Control System (ACS)

CHAPTER 2

: ACS Installation

11/22/2017

AERCO International, Inc.

•

100 Oritani Dr.

•

Blauvelt, New York 10913

Page 15 of 139

OMM-0081_0F

Phone: 800-526-0288

GF-131

CHAPTER 2:

ACS INSTALLATION

INTRODUCTION

2.1

This Chapter provides the descriptions and procedures necessary to mount the ACS and
connect all boiler plant units and applicable sensors. Guidelines are also provided for
connection of an EMS or BAS being used with the system. Refer to the wiring diagram provided
in Appendix E when making all wiring connections to the ACS.

SITE SELECTION AND MOUNTING

2.2

Ensure that the site selected for installation of the ACS provides the following:

•

Access to single-phase AC power from 110 to 240 VAC, 60 Hz nominal

•

Sufficient clearances to permit maintenance and setup/operational tasks on the ACS.

2.2.1 Mounting the ACS

AERCO recommends that the ACS be wall-mounted using a sheet of plywood or other suitable
material. For easy viewing, the ACS controls and display should be at eye level. Mounting is
accomplished using three screws (not provided). The spacing for the three screws are indicated
on the rear of the ACS in millimeters. Figure 2-1 shows the rear of the panel enclosure and also
indicates the required spacing for the three mounting screws in inches. Proceed as shown
below, to mount the unit:

Mounting the ACS Controller

1.

First install a screw on the mounting surface at the top center location shown in Figure 2-1.
Leave a space of approximately 1/8 inch between the mounting surface and the head of the
screw.

2.

Remove the wiring compartment cover from the front of the ACS (see Figure 1-1) to provide
access to the slots for the two lower mounting screw locations.

3.

Hang the ACS on the installed top screw. Position the unit so it is level.

4.

Mark the locations for the two lower screws.

5.

Remove the ACS and drill two pilot holes for the lower screws.

6.

Replace the ACS on the installed top-center screw.

7.

Secure the ACS to the wall by installing the two lower screws. DO NOT over-tighten the
screws.

«
...
13
14
15
16
17
...
»

Summary of Contents for 5R5-384












































































































































Reviews:

No comments

Related manuals for 5R5-384

Ascotel Office 45

Brand: Aastra Pages: 40

Brand: Aastra Pages: 244

Brand: Aastra Pages: 30

Brand: Aastra Pages: 24

IntelliGate A150

Brand: Aastra Pages: 524

Ascotel IntelliGate 150

Brand: Aastra Pages: 228

Brand: Abus Pages: 12

Brand: Salda Pages: 16

Brand: ICP DAS USA Pages: 4

Brand: ICP DAS USA Pages: 6

EIP-2000 Series

Brand: ICP DAS USA Pages: 19

Brand: ICP DAS USA Pages: 4

Brand: Jabra Pages: 18

Brand: Watts Pages: 8

dmc1 Finish-Out

Brand: M&S Systems Pages: 8

Brand: YOKOGAWA Pages: 150

Brand: YOODA Pages: 3

Brand: YMGI Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands