Your Doorbell can be removed from your Z-Wave network at any time. You’ll need to use your Z-Wave
network’s main controller (or any other primary controller) to do this, the following instructions tell you
how to remove your doorbell from your Z-Wave network by using Aeon Labs’ Z-Stick or Minimote
controller. If you are using other products as your main Z-Wave controller, please refer to the part of
their respective manuals that tells you how to remove devices from your network.
If you’re using a Z-Stick
1. If your Z-Stick is plugged into a gateway or a computer, unplug it.
2. Take your Z-Stick to your Doorbell.
3. Press and hold the Action Button on your Z-Stick for 2 seconds then let go. The LED should begin to
blink rapidly on your Z-Stick.
4. Press the Action Button on your Doorbell.
5. If your Doorbell has been successfully removed from your network, its Network LED will start to
blink. If the removal was unsuccessful, the Network LED will not blink.
6. Press the Action Button on the Z-Stick to take it out of removal mode
.
If you’re using a Minimote:
Removing your Doorbell from a Z-Wave network.
You’re able to adjust your Doorbell’s ringtone volume manually by using the “Volume -“ or “”
buttons. You can reduce its volume via short press on the “Volume -” button or increase the volume via
short press on the “” button, at the same time the default doorbell music will be triggered to allow
you to hear the volume change. If you want to change to the next ringtone, press and hold the Volume
button, which will switch the current ringtone to the next one.
Technical specifications.
Model number: ZW056
Max working power: 2.5W.
Max volume: 80dB.
Operating temperature: 0
to 40
for Doorbell, 0
to 55
for Wireless Button.
Storage temperature: -20
to 70 .
Wireless Button’s battery: Lithium cell CR2450 3 volt battery.
Water proofing of Wireless Button: IP54.
C
C
C
C
C
C
Reset your Doorbell.
Low battery checking for Wireless Button.
1. Take your Minimote to your Doorbell.
2. Press the Remove Button on your Minimote.
3. Press the Action Button on your Doorbell.
4. If your Doorbell has been successfully removed from your network, its Network LED on your Doorbell
will start to blink. If the removal was unsuccessful, the Network LED will not blink.
5. Press any button on your Minimote to take it out of removal mode.
If your primary controller is missing or inoperable, you may wish to reset all of your Doorbell’s settings to
their factory defaults. To do this, press and hold the Action Button for 20 seconds and then release it. Your
Doorbell will now be reset to its original settings, and the Network LED will be solid for 2 seconds and then
start slow blinking as a confirmation.
If you find the Red LED on the Doorbell is blinking when you press the Wireless Button. You will need to
replace the CR2450 battery with a new battery, as the Red LED indicates low battery power.
Warranty.
Aeon Labs warrants to the original purchaser of Products that for the Warranty Period (as defined
below), the Products will be free from material defects in materials and workmanship. The foregoing
warranty is subject to the proper installation, operation and maintenance of the Products in
accordance with installation instructions and the operating manual supplied to Customer. Warranty
claims must be made by Customer in writing within thirty (30) days of the manifestation of a problem.
Aeon Labs' sole obligation under the foregoing warranty is, at Aeon Labs' option, to repair, replace
or correct any such defect that was present at the time of delivery, or to remove the Products and to
refund the purchase price to Customer.
The "Warranty Period" begins on the date the Products is delivered and continues for 12 months.
Any repairs under this warranty must be conducted by an authorized Aeon Labs service
representative and under Aeon Labs' RMA policy. Any repairs conducted by unauthorized persons
shall void this warranty.
Excluded from the warranty are problems due to accidents, acts of God, civil or military authority,
civil disturbance, war, strikes, fires, other catastrophes, misuse, misapplication, storage damage,
negligence, electrical power problems, or modification to the Products or its components.
Aeon Labs does not authorize any person or party to assume or create for it any other obligation or
liability in connection with the Products except as set forth herein.
Aeon Labs will pass on to Customer all manufacturers’ Material warranties to the extent that they are
transferable, but will not independently warrant any Material.
Customer must prepay shipping and transportation charges for returned Products, and insure the
shipment or accept the risk of loss or damage during such shipment and transportation. Aeon Labs
will ship the repaired or replacement products to Customer freight prepaid.
IN NO EVENT SHALL AEON LABS BE LIABLE FOR ANY INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL OR
CONSEQUENTIAL DAMAGES, OR DAMAGES FOR LOSS OF PROFITS, REVENUE, OR USE INCURRED BY
CUSTOMER OR ANY THIRD PARTY, WHETHER IN AN ACTION IN CONTRACT, OR TORT, OR OTHERWISE EVEN
IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. AEON LABS' LIABILITY AND CUSTOMER'S EXCLUSIVE
REMEDY FOR ANY CAUSE OF ACTION ARISING IN CONNECTION WITH THIS AGREEMENT OR THE SALE OR
USE OF THE PRODUCTS, WHETHER BASED ON NEGLIGENCE, STRICT LIABILITY, BREACH OF WARRANTY,
BREACH OF AGREEMENT, OR EQUITABLE PRINCIPLES, IS EXPRESSLY LIMITED TO, AT AEON LABS' OPTION,
REPLACEMENT OF, OR REPAYMENT OF THE PURCHASE PRICE FOR THAT PORTION OF PRODUCTS WITH
RESPECT TO WHICH DAMAGES ARE CLAIMED. ALL CLAIMS OF ANY KIND ARISING IN CONNECTION WITH THIS
AGREEMENT OR THE SALE OR USE OF PRODUCTS SHALL BE DEEMED WAIVED UNLESS MADE IN WRITING
WITHIN THIRTY (30) DAYS FROM AEON LABS'S DELIVERY, OR THE DATE FIXED FOR DELIVERY IN THE EVENT
OF NONDELIVERY.
THE INDEMNITY AND WARRANTY IN ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER INDEMNITIES
OR WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
FCC NOTICE (for USA)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY
UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.SUCH MODIFICATIONS COULD VOID THE USER’S
AUTHORITY TO OPERATE THE EQUIPMENT.
STORE INDOORS WHEN NOT IN USE. SUITABLE FOR DRY LOCATIONS. DO NOT IMMERSE IN WATER. NOT FOR
USE WHERE DIRECTLY EXPOSED TO WATER.
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired
1
2
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consul the dealer or an experienced radio/TV technician for help.
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection
facilities.
Contact your local government for information regarding the collection systems available.
We reserve the right to modify specifications.
Warning
Certifications (regional):
Z-Wave and Z-Wave Plus are
registered trademarks of Sigma
Designs and its subsidiaries in the
United States and other countries
Version: 501005600003-AB www.aeotec.com
Pair the Wireless Button with your Doorbell.
Download new ringtones to your Doorbell from your PC.
This procedure should only be used when the complimentary Wireless Button is missing or inoperable and
you have another new Wireless Button that would be paired with your Doorbell. To do this, press the “Volume
–” button and “” button at the same time once, the Network LED will fast blink, which indicates it
has entered into pairing mode, at this time, press the Wireless Button once, your Wireless Button should
now be paired with the Doorbell allowing it to trigger the doorbell ringtone.
Use the Micro USB cable to connect Doorbell to your PC. Your PC will detect the removable storage after
a few seconds, and then you’ll find it in the “Device with Removable Storage” section.
Double click the “Removable Disk (G:)” to open it.
Now copy/drag the MP3 music from the PC hard disk to the Doorbell’s flash memory.
Wait until you have finished copying the MP3 files.
Do not disconnect the USB port until copying has completed.
The transfer order of MP3 file in the process of copying is also the sequence that will play in Doorbell.
The new added MP3 files will be pushed back to the end of the list in the sequence it is played.
When a MP3 file is renamed in “Removable storage”, it will be moved to the end of the sequence list
automatically.
Note: When the Doorbell enters into pairing mode, it has a 8 seconds timeout for pairing, so you need to
press the new Wireless Button once within the 8 seconds pairing timeout.
Note:
1.
2.
3.
4.
1.
2.
3.
4.
Customer shall indemnify, defend, and hold Aeon Labs and Aeon Labs' affiliates, shareholders,
directors, officers, employees, contractors, agents and other representatives harmless from all
demands, claims, actions, causes of action, proceedings, suits, assessments, losses, damages,
liabilities, settlements, judgments, fines, penalties, interest, costs and expenses (including fees and
disbursements of counsel) of every kind (i) based upon personal injury or death or injury to property
to the extent any of the foregoing is proximately caused either by a defective product (including strict
liability in tort) or by the negligent or willful acts or omissions of Customer or its officers, employees,
subcontractors or agents, and/or (ii) arising from or relating to any actual or alleged infringement or
misappropriation of any patent, trademark, mask work, copyright, trade secret or any actual or alleged
violation of any other intellectual property rights arising from or in connection with the products, except
to the extent that such infringement exists as a result of Aeon Labs' manufacturing processes.
FCC ID: XBAZW056
CONFORMS TO UL STD.60950-1
CERTIFIED TO CSA STD.CC 22.2 No.60950-1-07
Supported audio formats: MP3 or WAV.
Operating distance: Up to 500 feet/150 metres outdoors in normal mode or 300 feet/100 metres
outdoors in ringtone mode.
AC Input:
Version Input (Standby Power)
Working band
AU
230V 50Hz, Max: 0.5W
921.42MHz
BR
220V 60Hz, Max: 0.5W
921.42MHz
CN
220V 50Hz, Max: 0.5W
868.40MHz
EU
230V 50Hz, Max: 0.5W
868.42MHz
IL
230V 50Hz, Max: 0.5W
916.02MHz
IN
230V 50Hz, Max: 0.5W
865.20MHz
UK
230V 50Hz, Max: 0.5W
868.42MHz
US
120V 60Hz, Max: 0.45W
908.42MHz
operation. This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Advanced functions.
