ELECTRICAL SPECIFICATIONS
Nominal Range:
2A, 150A
Measurement Range:
2A:
0.01 to 2.4A
150A:
0.1 to 200A
Transformation Ratio:
Voltage output
Output Signal:
2A:
1000mV/A
150A:
10mV/A
Accuracy and Phase Shift*:
2A Range - Accuracy
0.01 to 0.1A:
5% Reading ± 2mV
0.1 to 1A:
3% Reading ± 1mV
1 to 2A:
1% Reading
2 to 2.4A:
1% Reading
Phase Shift: Not specified
150A Range - Accuracy
0.1 to 1A:
3% Reading ± 200µV
1 to 20A:
2% Reading ± 200µV
20 to 80A:
1% Reading
80 to 150A:
3% Reading
150 to 200A: Not specified
150A Range - Phase Shift
0.1 to 1A:
Not specified
1 to 20A:
3°
20 to 80A:
2°
80 to 150A:
3°
150 to 200A:
4°
(*Reference conditions: 18°C to 28°C , 20 to 75% R
H,
external magnetic field <40 A/m, 48 to 65H z si ne w ave,
distortion f actor l ess than 1%, no D
C component, no
external current carrying conductor, test sample centered.)
Load impedance > 1M
.
Overload:
240A for 10 min ON, 30 min OFF
Frequency Range:
40 to 10kHz
Limit Operating Conditions:
200A permanently to 1kHz; Derating above
3kHz: 200A x (1/0.333F), F in kHz
Crest Factor:
2A:
3 @ 2A Peak w/ an error (due to CF) of 3%
150A:
3 @ 150A Peak w/ an error (due to CF) of 3%
Working Voltage:
600Vrms
Common Mode Voltage:
600Vrms
Influence of Adjacent Conductor:
< 15mA/A at 50Hz
Influence of DC on AC signal:
2A Range:
DC Current < 1A, < 3%
150A Range:
DC Current < 10A, < 10%
Influence of Conductor Position in Jaw:
0.5% of mV output @ 50/60Hz
Influence of Frequency:
2A Range:
40Hz to 1kHz: 10% of mV output
1kHz to 10kHz: 10% of mV output
150A Range:
40Hz to 1kHz: 5% of mV output
1kHz to 10kHz: 15% of mV output
Influence of Temperature:
200 ppm/°K, or 0.2% of mV output per 10°K
Influence of Humidity (10 - 90% RH):
0.2% of mV output per 10°K @ 18° to 28°C
MECHANICAL SPECIFICATIONS
Operating Temperature:
14° to 131°F (-10° to +55°C)
Storage Temperature:
-40° to 158°F (-40° to +70°C)
Operating Relative Humidity:
10° to35°C 85% RH (without roll-off above 35°C)
Maximum Cable Diameter:
One Ø 0.78” (20mm), bus bar 20 x 5 mm
Case Protection:
IP 40 (IEC 529)
Drop Test:
Test per IEC 68-2-32:
1.0 m drop on 38mm of Oak on concrete
Mechanical Shock:
Test per IEC 68-2-27
Vibration:
Test per IEC 68-2-6
Dimensions:
5.47 x 2.00 x 1.18" (139 x 51 x 30mm)
Weight:
180g (6.5oz)
Polycarbonate Material:
Jaws: Polycarbonate with 10% fiberglass charge,
Red UL 94 V0
Case: Polycarbonate 920A Gray
Opening Operations - Life:
> 50,000
Output:
Double/reinforced insulated 5 ft (1.5m) lead with
safety 4mm banana plug
SAFETY SPECIFICATIONS
Electrical:
Double insulation or reinforced insulation between
the primary or secondary and the outer case of the
handle conforms to IEC 1010-2-32.
Common Mode Voltage:
600V Category III, Pollution Degree 2
Dielectric Strength:
5550V, 50/60Hz between primary, secondary
and the outer case of the handle
Electromagnetic Compatibility:
EN 50081-1 Class B
EN 50082-2 Electrostatic discharge
IEC 1000-4-2
Radiated field IEC 1000-4-3
Fast transients IEC 1000-4-4
Magnetic field at 50/60Hz IEC 1000-4-8
ORDERING INFORMATION
AC Current Probe MN373 ................. Cat #2116.28
Accessories:
Banana plug adapter
(to non-recessed plug) .......................
Cat #1017.45
E192383
2.56"
(65 mm)
5.47"
(139 mm)
.83"
(21 mm)
Black
Red
.73"
2.00"
(51 mm)
(18.5 mm)
.1.18"
(30 mm)
Tactical
Barrier
(keep hands below
this barrier)
w
w
w
.
G
lo
ba
lTe
st
Su
pp
ly
.c
om
Fin
d Q
ua
lit
y P
ro
du
ct
s O
nli
ne
a
t:
sa
le
s@
G
lo
ba
lTe
st
Su
pp
ly.c
om
