AEM 30-0312 Instruction Manual Download Page 7

Page: 7 / 9

Gauge Installation

Installation using supplied bracket

Installation w ithout bracket, using rubber band

A 2-1/6" (52mm) hole is required to mount the X-Series gauge.  A bracket and thumbscrews are provided to facilitate
installation into a panel or gauge pod.  In some cases, the gauge cup may be pushed into a mounting  hole  causing  an
interference fit strong enough to retain the gauge; the supplied rubber band may be fit to the gauge to create a tighter fit in
mounting holes slightly larger than 52mm.  It is, however, recommended that gauges be mounted securely  using  the
supplied bracket to ensure they never become loose and cause a hazard during vehicle operation.

Note:

The gauge is not water-proof and should not be installed in a location with exposure to water or snow. Damage

caused by water ingress will not be covered under warranty.

AEMnet Channels

Display Label

Description

Source

AF.Fb

Inj 1 LambdaFB

Infinity EMS

AFr.1

Lambda 1

AFR

EMS Series 2 / EMS-4 / Infinity

AFr.2

Lambda 2

AFR

EMS Series 2 / EMS-4 / Infinity

ALt

Altitude

VDM

bAtt

Battery Volts

EMS Series 2 / EMS-4 / Infinity

bSt.d

Boost Control Duty

Infinity EMS

bSt.t

Boost Target

psig

kPa

Infinity EMS

CUt.S

SparkCut [RPM]

rpm

Infinity EMS

CYL.1

Lambda 1

AFR

4 Channel UEGO set on MODE 1

CYL.1

Lambda 1

AFR

4 Channel UEGO set on MODE 3

CYL.1

Lambda 1

AFR

4 Channel UEGO set on MODE 6

CYL.2

Lambda 2

AFR

4 Channel UEGO set on MODE 1

CYL.2

Lambda 2

AFR

4 Channel UEGO set on MODE 4

CYL.2

Lambda 2

AFR

4 Channel UEGO set on MODE 6

CYL.3

Lambda 3

AFR

4 Channel UEGO set on MODE 1

CYL.3

Lambda 3

AFR

4 Channel UEGO set on MODE 3

CYL.3

Lambda 3

AFR

4 Channel UEGO set on MODE 6

CYL.4

Lambda 4

AFR

4 Channel UEGO set on MODE 1

CYL.4

Lambda 4

AFR

4 Channel UEGO set on MODE 4

CYL.4

Lambda 4

AFR

4 Channel UEGO set on MODE 7

CYL.5

Lambda 5

AFR

4 Channel UEGO set on MODE 2

CYL.5

Lambda 5

AFR

4 Channel UEGO set on MODE 3

CYL.5

Lambda 5

AFR

4 Channel UEGO set on MODE 7

CYL.6

Lambda 6

AFR

4 Channel UEGO set on MODE 2

CYL.6

Lambda 6

AFR

4 Channel UEGO set on MODE 4

CYL.6

Lambda 6

AFR

4 Channel UEGO set on MODE 7

Summary of Contents for 30-0312










Search results

Summary of Contents for 30-0312

Reviews:

Brands by name

Popular brands

AEM 30-0312, Instruction Manual

Search results

Summary of Contents for 30-0312

Reviews:

Brands by name

Popular brands