AEM Performance Electronics 30-8300 Instruction Manual Download Page 6 | Manualshive

Page: 6 / 9

background image

Rx Message 2 receives the PWM duty value for the output. The PWM control of the outputs is designed to

regulate the speed of devices like pumps and fans. If message 2 is present then all of the outputs will

become PWM duty cycle outputs with a base frequency of 100hz.The requested duty cycle can vary

between 0 –

100%. Any outputs that you do not want to have a PWM should have a value of 255. If this

message does not update within 500mS then the PDU-8 will treat all channels with simple ON/OFF control.

PDMDutyOut0#

is an unsigned 8 bit number with a scale of 0.392157 and an offset of 0 (0-100%).

PDU-8 Rx Message 2, 0x000A0630 (for unit 1) timeout if not updated within 500mS

6/9/2020 –

Document Number: 10-8300-EV

© 2020 AEM Performance Electronics

«
...
4
5
6
7
8
...
»

Summary of Contents for 30-8300










Reviews:

No comments

Related manuals for 30-8300

Brand: E-T-A Pages: 48

Mains Multiplier 6+

Brand: Essential Audio Tools Pages: 12

Brand: QSC Pages: 21

4/PWR-220 v4/SMS

Brand: NetPing Pages: 23

COPIER GUARDIAN II

Brand: Smart power Pages: 2

Brand: PowerWalker Pages: 19

Brand: Inter-m Pages: 13

Brand: EuroLite Pages: 15

SURGE GUARD 44280

Brand: Southwire Pages: 2

Brand: Mastervolt Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands