background image

3.

Push the plastic connection back in

and place the water container back

into position.

4.

To continue the programme press

the Start/Pause button.

10.3 

Cleaning the condenser

If the symbol   

Condenser

 flashes on

the display, inspect the condenser and

its compartment. If it is dirty, clean it. Do

the check not less than once a 6 months.

WARNING!

Do not touch the metal

surface with bare hands. Risk

of injury. Wear protective

gloves. Clean carefully to

avoid damaging the metal

surface.

To inspect:

1.

Open the door. Pull the filter up.

2.

Open the condenser cover.

3.

Turn the lever to unlock the

condenser lid.

4.

Lower the condenser lid.

5.

If necessary, remove the fluff from

the condenser and its compartment.

You can use a wet cloth and/or a

vacuum cleaner with a brush

attachment.

6.

Close the condenser lid.

7.

Turn the lever until it clicks into

position.

8.

Put the filter back.

10.4 

Cleaning the drum

WARNING!

Disconnect the appliance

before you clean it.

Use a standard neutral soap detergent to

clean the inner surface of the drum and

drum lifters. Dry the cleaned surfaces

with a soft cloth.

18

 

www.aeg.cn

Summary of Contents for T7DEE834





























Reviews: