24
24
38
o
33.9
o
(Right)
Right side of outside corner
1. Bottom edge of molding against
fence
2. Turning table set right 31.6
o
3. Save left end of cut
45
o
30
o
(Left)
Left side of inside corner
1. Top edge of molding against
fence
2. Turning table set right 35.3
o
3. Save left end of cut
45
o
30
o
(Left)
Right side of inside corner
1. Bottom edge of molding against
fence
2. Turning table set left 35.3
o
3. Save left end of cut
45
o
30
o
(Left)
Left side of outside corner
1. Bottom edge of molding against
fence
2. Turning table set left 35.3
o
3. Save right end of cut
45
o
30
o
(Left)
Right side of outside corner
1. Top edge of molding against fence
2. Turning table set right 35.3
o
3. Save right end of cut
45
o
30
o
(Right)
Left side of inside corner
1. Bottom edge of molding against
fence
2. Turning table set right 35.3
o
3. Save right end of cut
45
o
30
o
(Right)
Right side of inside corner
1. Top edge of molding against
fence
2. Turning table set left 35.3
o
3. Save right end of cut
45
o
30
o
(Right)
Left side of outside corner
1. Top edge of molding against
fence
2. Turning table set left 35.3
o
3. Save left end of cut
45
o
30
o
(Right)
Right side of outside corner
1. Bottom edge of molding against
fence
2. Turning table set right 35.3
o
3. Save left end of cut
NESTING CROWN MOLDING AGAINST THE MITRE FENCE
6HH¿JXUHV
To nest pieces of crown molding less than 89 mm (3-1/2 in.)
tall:
Ŷ
Set the bevel angle at 0° and the mitre angle at 45° to either
the left or the right.
Ŷ
Lay the crown molding on the saw with its bottom edge resting
at a natural angle flush against the fence and its top edge
resting flush against the turning table, this is called “nesting”.
Ŷ
Nest and secure the crown molding against mitre fence using a
spring clamp (not included) and hold crown molding securely.
Ŷ
Before turning on the saw, perform a dry run of the cutting
operation to make sure that no problems will occur when the
cut is made.
Ŷ
Pull the lower guard lock out lever to right side to unlock the
lower guard.
Ŷ
*UDVSWKHVDZKDQGOHILUPO\6TXHH]HWKHVZLWFKWULJJHU$OORZ
several seconds for the blade to reach maximum speed.
Ŷ
Slowly lower the blade into and through the crown molding.
Ŷ
Release the switch trigger and allow the saw blade to stop
rotating before raising the blade out of the crown molding and
removing the crown molding from the turning table.
CUTTING WARPED MATERIAL
6HH¿JXUHV
When cutting warped material, always make sure it is positioned on
the turning table with the convex side against the fence as shown
LQ¿JXUH
If the warped material is positioned the wrong way as shown in
¿JXUHLWZLOOSLQFKWKHEODGHQHDUWKHFRPSOHWLRQRIWKHFXW
WARNING
To avoid kickback and to avoid serious personal injury, never
position the concave edge of bowed or warped material against
the fence.
ADJUSTMENTS
WARNING
To prevent accidental starting that could cause serious personal
injury, always remove the battery pack from the product when
making adjustments.
The product has been adjusted at the factory for making very
accurate cuts. However, some of the components might have been
jarred out of alignment during shipping. Also, over a period of time,
readjustment will probably become necessary due to wear. After
unpacking the saw, check the following adjustments before you
begin using saw. Make any readjustments that are necessary and
periodically check the parts alignment to make sure that the saw is
cutting accurately.
PIVOT ADJUSTMENTS
NOTE:
These adjustments were made at the factory and normally
GRQRWUHTXLUHUHDGMXVWPHQW
TRAVEL PIVOT ADJUSTMENT
Ŷ
The saw arm should rise completely to the up position by itself.
Ŷ
If the saw arm does not raise by itself or if there is play in the
pivot joints, have saw repaired at your nearest authorised
service centre.
TO ADJUST THE BEVEL PIVOT
The product should bevel easily by loosening the bevel lock
knob and tilting the saw.
NOTE:
To obtain right bevel angles, pull the single/ dual bevel
selector out and tilt the saw to the desired angle.
If movement is tight or if there is play in the pivot, have saw repaired
at your nearest authorised service centre.
45° BEVEL ADJUSTMENT
6HH¿JXUH
Ŷ
Remove the battery pack from the product.
Ŷ
Loosen the bevel lock knob and set the saw arm at 45° bevel.
NOTE:
To obtain right bevel angles, pull the single/ dual bevel
selector out and tilt the saw to the desired angle.
Ŷ
Check the accuracy of the blade to the turning table as
