manualshive.com logo in svg

AEG OKO FAVORIT 60850 i, User Information, Page: 25 / 40

Share
Download
AEG OKO FAVORIT 60850 i User Information Download Page 25

25

Malfunction

Possible cause

Remedy

The cycle indicator for the 
selected dishwashing cycle 
is flashing:
the control indicator WA-
TER/EAU is lit,
fault code 

Å 10

is dis-

played in the multi-display
(Problems with water in-
let).

Water tap is blocked with 
limescale or faulty.

Check the water tap and 
have it repaired if necessary.

The tap is turned off.

Turn the tap on.

The filter (where present) in 
the threaded hose fitting 
on the tap is blocked.

Clean the filter in the 
threaded hose fitting.

Filters in the base of the 
washing compartment are 
blocked.

Press the button for the 
dishwashing cycle that has 
started;
then abort the dishwashing 
cycle  (see section: Starting 
a dishwashing cycle);
clean filters (see section: 
Cleaning the filters). 

Water inflow hose
has not been correctly posi-
tioned.

Check the position of the 
hose.

The cycle indicator for the 
selected dishwashing cycle 
is flashing,
fault code 

Å 10

 is dis-

played in the multi-display
(there is water in the dish-
washer’s internal dispens-
er).

The sink outlet is blocked.

Clean out sink outlet.

Water drain hose
has not been correctly posi-
tioned.

Check the position of the 
hose.

Fault code 

Å 30

 is dis-

played in the multi-dis-
play.

The anti-flood system has 
been triggered.

First shut off the water tap, 
then switch off the appli-
ance and contact the Cus-
tomer Care Department.

The control indicator 
DEUR/PORTE is lit.

The door of the dishwasher 
is open.

Close the dishwasher door.

The control indicator ZEEF/
FILTRE is lit.

The indicator ZEEF/FILTRE is 
there to remind you to 
check the dishwasher’s fil-
ters occasionally and to 
clean them, if necessary. It 
lights up at regular inter-
vals, regardless of how 
clean the filters are.

The indicator goes out auto-
matically at the start of the
next dishwashing cycle.

Summary of Contents for OKO FAVORIT 60850 i









































Reviews:

No comments