AEG LAVAMAT 50550 ELECTRONIC User Information Download Page 41

Setting up and connection instructions

41

Setting up and connection instructions

Safety Instructions for Installation

Do not tilt the washing machine onto its front or onto its right side 
(looking from the front). Electrical components could get wet!

Check the washing machine for transport damage. Never connect a 
damaged unit. Consult your supplier in the event of damage.

Ensure that all parts of the transport safeguard have been removed 
and that the splash guard is fitted to the unit, see ”Removing the 
Transport Safeguard”. Otherwise, damage to the unit or to adjacent 
furniture could occur during spinning.

Always insert the plug into a correctly installed PE socket.

In the case of permanent installation: A permanent installation may 
only be made by an authorised specialist.

Before putting the unit into operation, ensure that the rated voltage 
and current type shown on the unit's rating plate are the same as the 
mains voltage and current type at the installation location. The re-
quired electrical fuse is also shown on the rating plate.

Should work be carried out on the water supply installations in order 
to allow the machine to be connected properly to the water supply, 
this work must be carried out by an authorised installer.

Should work be carried out on the mains supply in order to allow the 
machine to be connected properly to the electricity supply, this work 
must be carried out by an authorised electrician.

The mains cable may only be replaced by the Customer Service or by 
an authorised specialist.

Summary of Contents for LAVAMAT 50550 ELECTRONIC

























































Reviews: