AEG L7WEE741BI User Manual Download Page 43

Page: 43 / 52

15.10

Frost precautions

If the appliance is installed in an area

where the temperature can reach values

around 0° C or drop below, remove the

remaining water from the inlet hose and

the drain pump.

Disconnect the mains plug from the

mains socket.

Close the water tap.

Put the two ends of the inlet hose in

a container and let the water flow out

of the hose.

Empty the drain pump. Refer to the

emergency drain procedure.

When the drain pump is empty,

install the inlet hose again.

WARNING!

Make sure that the

temperature is higher than 0

°C before you use the

appliance again.

The manufacturer is not

responsible for damages

caused by low temperatures.

16.

TROUBLESHOOTING

WARNING!

Refer to Safety chapters.

16.1

Introduction

The appliance does not start or it stops during operation.
First try to find a solution to the problem (refer to the table). If the problem persists,

contact the Authorised Service Centre.

WARNING!

Deactivate the appliance before carrying out any check.

In case of major problems, the acoustic signals operate, the display shows an

alarm code and the

Inicio/Pausa

button may flash continuously:

•

- The mains supply is unstable. Wait until the mains supply is stable.

•

- No communication between electronic elements of the appliance. Switch it

off and switch on again. The programme was not finished properly or the appliance

stopped too early. If the alarm code appears again, contact the Authorised Service

Centre.

•

- The anti-flood device is on. Disconnect the appliance and close the water

tap. Contact the Authorised Service Centre.

•

- The appliance does not fill with water properly. After the proper check, start

the appliance again by pressing Inicio/Pausa button the appliance tries to resume

the cycle . If the error persists the alarm code will appear again.

•

- The appliance does not drain the water.

•

- The appliance door is open or not closed correctly. Please check the door!

If the appliance is overloaded, remove some items from the drum

and/or hold the door shut while touching the Inicio/Pausa button until
the indicator

stops flashing (see the picture below).

ENGLISH

Summary of Contents for L7WEE741BI





















































Search results

Summary of Contents for L7WEE741BI

Reviews:

Related manuals for L7WEE741BI

Brands by name

Popular brands

AEG L7WEE741BI, User Manual

Search results

Summary of Contents for L7WEE741BI

Reviews:

Related manuals for L7WEE741BI

Brands by name

Popular brands