AEG FSE83847P User Manual Download Page 27

Problem and alarm code

Possible cause and solution

The appliance is switched

on but does not operate.

The display shows Power

Fail.

• Power supply is out of the operating range. The wash

cycle is temporarily interrupted and resumes automati‐

cally once the power is restored.

The appliance switches off

during operation.

• Complete power outage. The wash cycle is temporarily

interrupted and resumes automatically once the power

is restored.

Once you have checked the appliance,

deactivate and activate the appliance. If

the problem occurs again, contact an

Authorised Service Centre.
For alarm codes not described in the

table, contact an Authorised Service

Centre.

Before contacting an

Authorised Service Centre,

write down the PNC number.

Refer to "Basic settings".

WARNING!

We do not recommend using

the appliance until the

problem has been

completely fixed. Unplug the

appliance and do not plug it

in again until you are certain

that it operates correctly.

11.1 The dishwashing and drying results are not satisfactory

Problem

Possible cause and solution

Poor washing results.

• Refer to "Daily use""Hints and tips" and the basket

loading leaflet.

• Use more intensive washing programme.

• Activate the ExtraPower option to improve the washing

results of a selected programme.

• Clean spray arm jets and filter. Refer to "Care and

Cleaning".

Poor drying results.

• Tableware was left for too long inside the closed appli‐

ance. Activate the function AirDry to set the automatic

opening of the door and to improve the drying perform‐

ance.

• There is no rinse aid or the dosage of rinse aid is not

sufficient. Fill the rinse aid dispenser or set the dosage

of rinse aid to a higher level.

• The quality of the rinse aid can be the cause.

• Always use rinse aid, even with multi-tablets.

• Plastic items may need to be towel dried.

• The programme does not have the drying phase. Re‐

fer to "Programmes overview".

There are whitish streaks or

bluish layers on glasses and

dishes.

• The released quantity of rinse aid is too high. Adjust

the rinse aid dosage to a lower level.

• The quantity of detergent is too high.

ENGLISH

27

Summary of Contents for FSE83847P

































Reviews: