manualshive.com logo in svg

AEG FAVORIT 88070 Vi, User Information, Page: 37 / 48

Share
Download
AEG FAVORIT 88070 Vi User Information Download Page 37

37

Installation and connection instructions

1

Safety Information for the Installation

•

Only transport the dishwasher in an upright position, otherwise salt 
water may run out.

•

Before using the dishwasher for the first time, check for any damage 
caused in transport. Do not under any circumstances connect an ap-
pliance that is damaged. In the case of damage, please contact your 
supplier.

•

Never use the dishwasher if the mains cable, water inlet or drain hose 
are damaged; or if the control panel, work top or plinth area are 
damaged such that the inside of the appliance is freely accessible.

•

Always plug the mains plug into a correctly installed shockproof 
socket.

•

Permanent connection: a permanent connection must only be in-
stalled by a trained electrician.

•

Prior to using the appliance for the first time, ensure that the rated 
voltage and type of supply on the rating plate match that of the sup-
ply where the appliance is to be installed. The fuse rating is also to be 
found on the rating plate.

•

Multi-way plugs / connectors and extension cables must not be used. 
This could constitute a fire hazard through overheating.

•

The dishwasher’s cable must only be replaced by the Customer Care 
Department or a registered electrician.

•

A water inlet hose with safety valve must only be replaced by the 
Service Force engineer.

Summary of Contents for FAVORIT 88070 Vi

















































Reviews:

No comments