manualshive.com logo in svg

AEG FAVORIT 66609M0P, User Manual, Page: 17 / 20

Share
Download
AEG FAVORIT 66609M0P User Manual Download Page 17

11.2 

Cleaning the spray arms

Do not remove the spray arms. If the

holes in the spray arms are clogged,

remove remaining parts of soil with a thin

pointed object.

11.3 

External cleaning

• Clean the appliance with a moist soft

cloth.

• Only use neutral detergents.

• Do not use abrasive products,

abrasive cleaning pads or solvents.

11.4 

Internal cleaning

• Carefully clean the appliance,

including the rubber gasket of the

door, with a soft moist cloth.

• If you regularly use short duration

programmes, these can leave

deposits of grease and limescale

inside the appliance. To prevent this,

we recommend to run long duration

programmes at least 2 times per

month.

12. 

TROUBLESHOOTING

If the appliance does not start or it stops

during operation. Before you contact an

Authorised Service Centre, check if you

can solve the problem by yourself with

the help of the information in the table.

With some problems, the display

shows an alarm code.

Problem and alarm code

Possible solution

You cannot activate the ap-
pliance.

• Make sure that the mains plug is connected to the

mains socket.

• Make sure that there is no a damage fuse in the fuse

box.

The programme does not
start.

• Make sure that the appliance door is closed.
• Press 

Start

.

• If the delay start is set, cancel the setting or wait for the

end of the countdown.

• The appliance has started the procedure to recharge

the resin inside the water softener. The duration of the
procedure is approximately 5 minutes.

The appliance does not fill
with water.
The display shows 

.

• Make sure that the water tap is open.
• Make sure that the pressure of the water supply is not

too low. For this information, contact your local water
authority.

• Make sure that the water tap is not clogged.
• Make sure that the filter in the inlet hose is not clogged.
• Make sure that the inlet hose has no kinks or bends.

The appliance does not
drain the water.
The display shows 

.

• Make sure that the sink spigot is not clogged.
• Make sure that the drain hose has no kinks or bends.

The anti-flood device is on.
The display shows 

.

• Close the water tap and contact an Authorised Service

Centre.

ENGLISH

17

www.devicemanuals.eu/

Summary of Contents for FAVORIT 66609M0P





















Reviews:

No comments