manualshive.com logo in svg

AEG FAVORIT 64070, Instruction Book, Page: 35 / 48

Share
Download
AEG FAVORIT 64070 Instruction Book Download Page 35

Operating instructions

35

...the wash results are not satisfactory

The dishes are not clean

●

The wrong washing programme has been selected.

●

The dishes were arranged in such a way as to stop water 
reaching all parts of the surface. The baskets must not be 
overloaded.

●

The spray arms do not rotate freely due to wrong arrangement 
of the load.

●

The filters in the base of the washing compartment are dirty or 
incorrectly positioned.

●

Too little or no detergent has been used.

●

Where there are limescale deposits on the dishes; the salt 
container is empty or the wrong level of the water softener has
been selected.

●

The drain hose connection is not correct.

●

The salt container cap is not properly closed.

The dishes are wet and dull

●

Rinse aid was not used.

●

The rinse aid dispenser is empty.

There are streaks, milky spots or a bluish coating on glasses
and dishes

●

Decrease rinse aid dosing.

Water drops have dried onto glasses and dishes

●

Increase rinse aid dosing.

●

The detergent may be the cause. Contact the detergent 
manufacturer’s consumer care line.

152963040en per uk.qxp  22/03/2004  9.54  Pagina 35

Summary of Contents for FAVORIT 64070

















































Reviews:

No comments