manualshive.com logo in svg

AEG FAVORIT 50730, User Instructions, Page: 11 / 44

Share
Download
AEG FAVORIT 50730 User Instructions Download Page 11

Operating Instructions

11

Adjust the water softener to the water hardness setting for your area 
as shown in the table.

1 

It is only possible to adjust the water hardness setting when no pro-
gramme is running. If you have accidentally started a programme (a 
LED stays on permanently), the programme must be stopped by press-
ing the appropriate button.

0 

1.

The dishwasher must be switched off.

2. Manual setting:

Open the door on the dishwasher.

3.

Remove the lower basket from the 
dishwasher.

4.

Turn the water hardness switch 
to 0 or  1.

5.

Re-position the lower basket.

6. Electronic setting:

Press the softener and function but-
tons simultaneously and keep them 
pressed.

7.

In addition press the ON/OFF button.

8.

The LED indicators for the water softener and function buttons flash.

9.

Press the softener button again.
– At first the LED indicator for the water softener button will light up 

continuously for 5 seconds and then begin to flash.

– The number of flashes corresponds to the hardness setting.
– The sequence of flashes is repeated several times after a 5 second 

pause.

10.

Each time you press the water-softener button the hardness setting 
will go up by 1.
(Exception: Hardness setting 1 follows hardness setting 5).
– If the hardness setting is changed, the LED indicator for the water-

softener button will confirm the change by remaining illuminated 
continuously for 5 seconds and then flashing again.

– The number of flashes corresponds to the new hardness setting.
– The sequence of flashes is repeated several times after a 5 second 

pause.

11.

Once the hardness setting is correctly adjusted, press the ON/OFF but-
ton. 
The hardness setting is then stored.

Summary of Contents for FAVORIT 50730













































Reviews:

No comments