manualshive.com logo in svg

AEG FAVORIT 45001, User Manual, Page: 23 / 28

Share
Download
AEG FAVORIT 45001 User Manual Download Page 23

Capacity

Place settings

12

Installation instructions

Installation

Fitting under a counter

WARNING!

Make sure that the mains plug is disconnected from the mains socket during installation.

Put the appliance adjacent to a water tap and a water drain.

Install the appliance under a kitchen counter or work surface.

Make sure that the dimensions of the recess

agree with the given dimensions.

No further openings for the venting of the dish

-

washer are necessary, but only to let the water

fill, the drain hose and the power supply cable

pass through.

Make sure that there are no kinks in the water

hoses and that the water hoses are not squashed.

Adjusting the height of the appliance

Do these steps to adjust the height of the appliance:

1. Loosen or tighten the two front feet.

2. Loosen and remove the adjustable plinth.

3. Adjust the rear foot. Turn the screw in the middle of the front kick plate to the left or

to the right.

Make sure that the appliance is level to close and seal the door correctly. If the level of the

appliance is correct, the door does not catch on the sides of the cabinet. If the door does

not close correctly, loosen or tighten the adjustable feet until the appliance is level.

Adjusting the height of the plinth

Installation

23

Summary of Contents for FAVORIT 45001





























Reviews:

No comments