manualshive.com logo in svg

AEG FAVORIT 44630, Operating Instructions Manual, Page: 13 / 40

Share
Download
AEG FAVORIT 44630 Operating Instructions Manual Download Page 13

13

To deactivate the rinse aid indicator light be sure that the
dishwasher is off and then proceed as follows:

1.

Press 

INTENSIV 70°

and 

30 MIN

programme push buttons simultaneously.

2.

While keeping the programme push buttons 

INTENSIV 70°

and 

30 MIN

pressed 

switch on the dishwasher by pressing the On/Off push button. The On/Off 
indicator light comes on. At the same time, the indicator lights of the 

INTENSIV 70°

and 

30 MIN

push buttons start flashing.

3.

Press the 

30 MIN

push button, the correspondent indicator light keeps flashing 

while the indicator light of the 

INTENSIV 70°

push button turns off. At the same 

time the indicator light "

end of programme

" starts to flash.

4.

Press the 

30 MIN

push button again, the "

end of programme

" indicator light 

turns off, this means that the rinse aid indicator light has been deactivated.

5.

To memorise the operation, switch off the dishwasher by pressing the On/Off 
push button.

To reactivate the rinse aid indicator light follow the same process until the "

end of

programme

" indicator light starts to flash.

Adjusting the dose

According to the finish and drying results obtained
adjust the dose of rinse aid by means of the 6
position selector (C) (position 1 minimum dosage,
position 6 maximum dosage). 

Use the tip of a screwdriver to rotate the selector. 

Increase the dose if there are drops of water or
lime spots on the dishes after washing.

Reduce it if there are sticky whitish streaks on the
dishes.

SO451

SO449

BR02

152974 47/1en/UK  24-05-2002  9:35  Pagina 13

Summary of Contents for FAVORIT 44630









































Reviews:

No comments