AEG FAVORIT 40630 User Instructions Download Page 33 | Manualshive

Page: 33 / 48

AEG FAVORIT 40630 User Instructions Download Page 33

Operating Instructions

33

After remedying the error that is flashing in the

first or second

sequence

in the programme progress display, press the button for the

wash programme that had already started. The wash programme will
continue.
If the fault is displayed again, please contact your local Service Force
Centre.

3

For all other errors displayed, please contact Service Force, stating the
error code. (See chapter “Customer Service”).

The programme indicator
for the selected wash pro-
gramme is flashing,
the end wash programme
indicator is flashing in the
following

sequence: 2

short

flashes one after the other.

The siphon is blocked.

Clean out siphon.

The water drain hose has
not been correctly laid.

Check hose installation.

The end wash programme
indicator is flashing in the
following

sequence: 3

short

flashes, one after the other.

The leak prevention sys-
tem has been triggered.

Turn off the tap and con-
tact customer service.

Malfunction

Possible cause

Remedy

«
...
31
32
33
34
35
...
»

Summary of Contents for FAVORIT 40630

















































Reviews:

No comments