AEG CG 6400, Operating Instructions Manual

Page: 17 / 33

g
43
In the upper line, the display shows the
coffee strength as set in the "Jug"
menu, e.g. «
EXTRA-MILD JUG
». The
lower line of the display shows the
scrolling keys "<" or ">" and the
number of cups to be poured into the
jug, i.e. «
< > 4
».
3
If you wish to change the strength and
size of the cups for the jug function,
proceed as described in the section
„Setting the jug program (coffee
strength and fill level for jug
function)“, page 47.
0
If necessary, press the scrolling keys "<"
or ">" to increase or decrease in steps
of 2 cups the number of cups you wish
to pour into the jug (4, 6, 8, 10 cups).
3
If no keys are pressed within a few sec-
onds, the appliance will suggest the
next step in the display: «
CHOOSE
NUMBER OF COFFEE, PRESS
JUG KEY
».
0
Once you have chosen the desired
number of cups, confirm this by press-
ing the "JUG" key
(Fig. 19).
The display shows an advancing
progress bar with a percentage indica-
tion
«
40%
»
which represents the status of the
brewing operations.
Once the progress bar is complete and
the percentage has reached 100%, the
appliance stops brewing, and returns
automatically to the coffee mode.
0
Now you can remove the thermos jug
and close the lid (Fig. 20) to keep the
coffee warm for a longer period of
time.
3
If there are not enough coffee beans to
complete the requested operation, the
machine will stop the operation and
wait until the coffee bean container
has been filled and the "JUG“ key
(Fig. 19) has been pressed. For instance,
if you program 8 cups but you have
only beans for 6 cups, the appliance
will deliver 6 cups and then stop. Fill
the coffee bean container and then
press the "JUG“ key (Fig. 19). Once
you have done this, the appliance will
deliver just the last 2 cups, to reach the
programmed quantity of 8 cups.
If there is either too little water to
complete the requested operation, or
the waste coffee container is full, the
machine will stop the operation. The
jug has to be removed to fill the water
tank or to empty the waste coffee con-
tainer; at this point, the current pro-
gram is cancelled. After the error has
been rectified, the program must be
restarted. The amount of coffee
already in the jug must be taken into
consideration, so that the jug is not
over-filled.
3
If the message «
GROUND TOO
FINE ADJUST MILL
AND TURN KNOB
» is displayed, the
coffee is ground too fine. You should
change the grinding setting; see „Set-
ting the grinding texture“, page 46.
9 Using pre-ground coffee
This function allows you to brew pre-
ground coffee, e.g. decaffeinated
coffee.
1
Make sure that no ground coffee has
remained in the filler, and that no for-
eign objects enter the filler. The ground
coffee filler is not a storage container.
The ground coffee must be fed directly
into the brewing unit.
0
Turn the "Coffee strength / Pre-ground
coffee" knob (Fig. 21) to the desired
position
(for 1 cup) or (for 2
cups) to select the pre-ground coffee
function. This disables the coffee mill
function. The appliance displays e.g.
«
ESPRESSO CUP
PRE-GROUND 1 CUP
».
0
Open the lid of the ground coffee filler,
and scoop in the fresh ground coffee
(Fig. 22).
Use only the supplied measuring
spoon. Never add more than 2 level
measured scoops, otherwise either the
822_949_344 CG6400.book Seite 43 Mittwoch, 25. Oktober 2006 12:38 12