g
28
4. Frothing Milk
(Figures 13 to 18)
Hot steam can be used both for froth-
ing milk for cappuccino and for heat-
ing liquids.
3
For one cup of cappuccino, fill a large
cup up to ½ to 2/3 full with espresso
and then add the frothed milk.
Always use cool, fresh (low fat) milk to
achieve the best frothing results.
4.1. Frothing Milk
The type of coffee that was selected
last appears in the display.
CF 300:
0
Slide the movable tube on the swivel-
ling nozzle
all the way down
(Figure
13/A).
0
Turn the steam selector
clockwise
to
the
“Steam” position (Figure 17/A).
The appliance heats up. “HEATING UP”
appears in the display. After a short
while the “STEAM READY” display
appears.
0
Place a cup, half-filled at the most,
beneath the frothing nozzle (Figure
26).
0
Immerse the swivelling nozzle about
half way down inside the container
with the milk to be frothed so that air
can be drawn in unhindered. The swiv-
elling nozzle should not touch the base
of the container to avoid obstructing
the steam outlet.
0
Press the coffee selection button.
“STEAM” appears in the display.
0
You can
stop
the outlet of steam
– by turning the steam selector
anti-
clockwise
back to the O position, or
– by pressing the coffee selection but-
ton. “SET STEAM/WATER DIAL TO
ZERO” appears in the display.
0
Activate the outlet of steam briefly
after frothing milk to “blow clear” the
swivelling nozzle. Then clean any milk
residues from the swivelling nozzle
using a damp cloth. Move the movable
metal tube up and down during this
process.
CF 400:
Attach the frothed milk spout to the
steam nozzle (Figure 14):
0
Insert the knob for regulating the froth
(Figure 2/A) into the suction piece (Fig-
ure 2/B) and press
firmly
into place.
0
Insert the suction piece into the con-
nector (Figure 2/D), and connect the
milk discharge outlet (Figure 2/C) to
the connector.
0
Firmly
push the complete frothed milk
spout onto the steam nozzle until the
red seal on the steam nozzle is no
longer visible. As you do so, carefully
push against the grip for adjusting the
height of the steam nozzle.
0
Pour cold milk into the container sup-
plied. If you are frothing milk from the
container supplied you do not need the
flexible hose. The milk container is
attached directly to the frothed milk
spout (Figure 15).
3
You can also suck up the milk directly
from the carton using the flexible hose
(Figure 2/E). However, the milk carton
must not exceed the height of the milk
frothing nozzle. The flexible hose must
be inserted down into the milk carton.
0
Attach the flexible hose to the frothing
nozzle and insert the other end of the
flexible hose into the cold milk (Figure
18).
0
Place an empty cup underneath the
frothing nozzle (Figure 26).
0
Turn the steam selector
clockwise
to
the
“Steam” position (Figure 17/A).
The appliance heats up. “HEATING UP”
appears in the display. After a short
while the display “STEAM READY”
appears.
0
Press the coffee selection button.
“STEAM” appears in the display.
Important:
Using the knob for regulat-
ing the froth (Figure 2/A) you can set
the amount of froth (more or less
added air) and the temperature of the
milk to your taste (Figure 16/A, B, C).
To do this turn the knob slowly to the
right or to the left until you achieve
the desired result.
