AEG BHBS18B, Original Instructions Manual, Page: 14 / 16

14
14
KLJKHUJULWQXPEHUIRUUHPRYLQJOHVVPDWHULDODQGIRUD¿QHU¿QLVK
Replace the belt if it becomes damaged, clogged with debris or is
worn.
It is normal to sand and move the product back and forth along
the grain of the material. Sanding across the grain will work, but
produces a scratched and damaged surface.
WARNING
Dust from certain paints, coatings, and materials may cause
irritation or allergic reactions to the respiratory system. Dust from
wood, such as oak, beech, MDF, and others are carcinogenic.
Materials containing asbestos should only be worked or
SURFHVVHGE\TXDOL¿HGVSHFLDOLVWRSHUDWRUV
Use the dust collector or connect the dust port to a vacuum device
to reduce risks associated with dust particles.
All persons within the work area or nearby should wear dust masks
which offer appropriate protection.
Always wear safety goggles or safety glasses with side shields
during operation.
WARNING
Injuries may be caused, or aggravated, by prolonged use of a
tool. When using any tool for prolonged periods, ensure you take
regular breaks.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in accordance with
local, national and international provisions and regulations.
Ŷ The user can transport the batteries by road without further
requirements.
Ŷ Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation
and transport are exclusively to be carried out by appropriately.
trained persons and the process has to be accompanied by
corresponding experts.
When transporting batteries:
Ŷ Ensure that battery contact terminals are protected and
insulated to prevent short circuit.
Ŷ Ensure that battery pack is secured against movement within
packaging.
Ŷ Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice.
BATTERY PACK PROTECTION
The battery pack has overload protection that protects it from being
overloaded and helps to ensure long life. Under extreme stress the
battery electronics switch off the product automatically. To restart,
switch the product off and then on again. If the product does not
start up again, the battery pack may have discharged completely. In
this case it must be recharged in the battery charger.
MAINTENANCE
Remove the battery pack before starting any work on the product.
Always remove the sanding belt from the product before cleaning.
Failure to do so could cause serious personal injury.
$IWHUHDFKXVHUHPRYHWKHEHOWDQGGXVWFROOHFWRULI¿WWHG&OHDQ
the product thoroughly with a brush, dry cloth and vacuum cleaner.
WARNING
Do not use compressed air to blow dust from the product to
prevent serious eye injury.
The ventilation slots of the machine must be kept clear at all times.
Use only AEG accessories and AEG spare parts. Should
components need to be replaced which have not been described,
please contact one of our AEG service agents (see our list of
JXDUDQWHHVHUYLFHDGGUHVVHV
If needed, an exploded view of the tool can be ordered. Please state
the Article No. as well as the machine type printed on the label and
order the drawing at your local service agents or directly at:
Techtronic Industries (Australia) Pty. Ltd.
PO Box 1065
Mount Waverley VIC 3149
Tel. no. 1300 361 505
Australia
Techtronic Industries N.Z. Ltd .
PO Box 12-806
Penrose AUCKLAND 1642
Tel no. 0800 279 624
New Zealand
SYMBOLS
Safety alert
No-load speed
V Volts
Direct current
Regulatory Compliance Mark (RCM). Product
meets applicable regulatory requirements.
Please read the instructions carefully before
starting the machine.
Wear ear protection
Wear eye protection
Do not dispose of electric tools together with
household waste material. Electric tools and
electronic equipment that have reached the end of
their life must be collected separately and returned
to an environmentally compatible recycling facility.