AEG A18RS, Original Instructions Manual

Page: 15 / 20

15
ENGLISH
BATTERY AND CHARGER
Compatible battery pack
(not included)
Compatible
charger
(not included)
L1820R
L1820S
L1820SHD
L1825R
L1830R-X5
L1840S
L1840R
L1840SHD
L1850R
L1850SHD
L1860R
L1860R-X5
L1890R
AL18G
BL1218
BLK1218
BL18DP2-X5
BL18DPS
BL18S
Use AEG 18V battery and charger only
WARNING! Read all safety warnings, instructions,
illustrations and specifications provided with this power tool.
Failure to follow all instructions listed below may result in electric
shock, fire, and/or serious injury. Save all warnings and instruction
for future reference.
RECIPROCATING SAW SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
contact hidden wiring.
Cutting accessory contacting a “live” wire
may make exposed metal parts of the power tool “live” and could
give the operator an electric shock.
Use clamps or another practical way to secure and support the
workpiece to a stable platform.
Holding the workpiece by hand or
against your body leaves it unstable and may lead to loss of control.
Wear ear protectors.
Exposure to noise can cause hearing loss.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Wear ear protectors.
Exposure to noise can cause hearing loss.
Always wear goggles when using the machine. It is recommended
to wear gloves, sturdy non slipping shoes and apron.
Sawdust and splinters must not be removed while the machine is
running.
Always use the protective shields on the machine.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Wear a suitable dust protection mask.
Do not use cracked or distorted saw blades.
Plunge cuts without pre-drilling a hole are possible with soft
materials (wood, light building materials for walls). Harder materials
(metals) must first be drilled with a hole corresponding to the size of
the saw blade.
Always place the guide shoe on the workpiece when sawing.
When working in walls, ceiling, or floor, take care to avoid electric
cables and gas or water pipes.
Ambient temperature range for tool during operation is between 0°C
and 40°C.
Ambient temperature range for tool storage is between 0°C and
40°C.
The recommended ambient temperature range for the charging
system during charging is between 10°C and 38°C.
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING!
To reduce the risk of fire, personal injury, and
product damage due to a short circuit, never immerse your tool,
battery pack, or charger in fluid or allow a fluid to flow inside them.
Corrosive or conductive fluids, such as seawater, certain industrial
TECHNICAL DATA A18RS
Type Cordless reciprocating saw
Rated voltage 18 V
Stroke rate under no-load 0-3000 min-1
Length of stroke 28.5 mm
Weight without battery pack 2.3 kg
Noise Information
Measured values determined according to EN 62841. Typically, the A-weighted noise
levels of the tool are:
Sound pressure level (Uncertainty K=5dB(A))
Sound power level (Uncertainty K=5dB(A))
Wear ear protection!
L
pA
= 84.5 dB (A)
L
WA
= 95.5 dB (A)
Vibration Information
Vibration total values (triaxial vector sum) determined according to EN 62841.
Cutting board, a
h,B
(Uncertainty K = 1,5 m/s
2
)
Cutting wooden beam, a
h ,WB
(Uncertainty K = 1,5 m/s
2 )
a
h,B
=
15.0 m/s
2
a
h,WB
=
16.1 m/s
2
WARNING!
The declared vibration total values and the declared noise emission values given in this instruction manual have been measured in
accordance with a standardised test and may be used to compare one tool with another. They may be used for a preliminary assessment of
exposure.
The declared vibration and noise emission values represent the main applications of the tool. However, if the tool is used for different
applications, used with different accessories, or poorly maintained, the vibration and noise emission may differ. These conditions may
significantly increase the exposure levels over the total working period.
An estimation of the level of exposure to vibration and noise should take into account the times when the tool is turned off or when it is
running idle. These conditions may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration and noise, such as maintaining the tool and the
accessories, keeping the hands warm (in case of vibration), and organising work patterns.