HARDWARE INSTALLATION
READ ALL SAFETY DIRECTIONS & WARNINGS IN THE
COMPLETE INSTALLATION GUIDE LOCATED ON THE
PRODUCT WEBSITE, BEFORE INSTALLING. ENSURE YOUR
COMPUTER IS SWITCHED OFF AND ALL POWER CABLES
ARE REMOVED FROM THE SYSTEM BEFORE PROCEEDING
WITH INSTALLATION
1.
Remove any static electricity on your body before touching any electronic
component.
2.
Turn off and unplug the power cord to your computer and all of its peripherals.
Wait for your system to cool down before proceeding.
3.
Carefully insert the advoli
TM
TA4E Performance graphics card in the primary PCI
express x16 slot. Ensure graphics card is firmly secured.
4.
Connect one 6-pin PCI Express auxiliary power connector to the top right edge of
the advoli
TM
TA4E Performance graphics card where there is a power connector.
5.
Connect one 9-pin cable that comes with the advoli
TM
TA4E Performance
graphics card to the to the top right edge of the advoli
TM
TA4E Performance
graphics card and the other end of the cable to the motherboard USB 2.0 9-pin
header. Use the converter board that comes along with the cable if your
motherboard only has USB 3.0 header.
6.
Close the computer casing/panel once you have completed the installation of the
advoli
TM
TA4E Performance graphics card. You may now power up your
computer.
7.
Install driver from advoli website: www.advoli.com/drivers/ It is advised to use an
already existing HDMI/VGA connector on the motherboard with a paired monitor
to setup the driver for the graphics cards.
8.
You will need to have CAT 5e/6/7/+ cables in at least one of the four RJ45
sockets with a HDBaseT
TM
certified display or HDBaseT
TM
certified receiver
connected to a display in order to use the HDBaseT
TM
certified advoli
TM
TA4E
Performance graphics card. You may use all four RJ45 sockets paired with their
own display respectively. It is advised to use HDBaseT
TM
certified receivers to
ensure compatibility. We highly recommend the advoli
TM
HDBaseT RA1
Performance receiver for guaranteed performance, please note that the RA1
does not have ethernet.
9.
For further information on installing and using the product please go to the
product page on advoli website for the complete installation guide.
SPECIFICATION
BEFORE YOU INSTALL
MUST ITEMS
+ Read the full installation guide before beginning, it can be found at:
http://www.advoli.com/ta4eperformance/
Why?
You will make mistakes and you need to
read the warnings and safety related
items
!
+ For troubleshooting & questions, please go to:
http://www.advoli.com/support/
+ For drivers, please go to:
http://www.advoli.com/drivers/
+ We highly recommend to start with a fresh installation of your operating system as drivers
of other graphics cards are highly likely to interfere with driver of the TA4E Performance.
CONNECTION ILLUSTRATION
1:
2:
3:
VIDEO
# of HDBaseT Tx Channels
4 x RJ45 Connectors
HDCP 1.4 / 2.2
Compatible pass through
HDMI 1.4 / 2.0
Compatible pass through
300 MHz Pixel Clock Limitation
3D
Supported
Max Resolution
4K DCI 4096
×
2160 24Hz/25Hz/30Hz
4096
×
2160 30Hz @ chroma subsampling 4:4:4 8-bit
Max Resolution with all
channels active
4 x UHD 30Hz
Color Space
YUV, RGB
Chroma Subsampling
4:4:4, 4:2:2, 4:2:0
Color Depth
8-bit, 10-bit, 12-bit
HDR
4K HDR10 @ 24Hz, 4:2:0 chroma subsampling, 10-bit
AUDIO
Pass-Through
All formats supported by HDMI 1.4 and HDMI 2.0
All major digital audio formats, including: Dolby Digital,
DTS, Dolby TrueHD,
DTS HD-Master Audio, Dolby Pro Logic Iiz 7.1 & 9.1,
GRAPHICS / MXM
Model
AMD™ Embedded E9550
MXM Type
B
Desktop Software by AMD™
AMD™ Eyefinity™
Driver provided by AMD™
Win 10 – 64 Bit
Win 7 – 64 Bit
Win 7 – 32 Bit
Linux x86_64
Architecture
Polaris™
Video Control
Direct GMA™
Compute Units
5,8 TFLOPS
Memory
8GB GDDR5. 256 bit wide
GPU Power
95W
Video Encode/Decode
UVD4 for H.264, VC-1, MPEG-2, MPEG-4 part 2 decode
Projector Edge Blend
Available through Third Party Software
Display Bezel Correction
AMD™ Eyefinity™
CONTROLS
Diagnostics
HDBaseT™, Environmental & Electrical
Infrared
External IR Receiver Type A – 3 Pin Audio Jack Connector
External IR Transmitter Type A – 3 Pin Audio Jack
Connector
Emulated IR IN/OUT – RAW Data
RS232
External In/Out – 3 Pin Audio Jack Connector
Emulated Serial Port IN/OUT
(Virtual COM port)
max baud rate: 115,200 bps
CEC Compatible
Pass through
Ethernet
2 x RJ45 10/100 & Ethernet Pass Through on HDBaseT
EDID Management
Raw EDID pass through & EDID Serial Console Tools
PHYSICAL
Fansink
Copper with 2 dual ball bearing fans
Dimensions
L: 167mm H: 120mm W: 39mm L: 6.6in H: 4.7in W: 1.5in
Dimensions of Packaging
L 350mm H: 70mm W: 195mm L: 13.8in H: 2.8in W: 7.7in
Weight of Product
566g +/- 10g OR 19.97oz +/- 0.35 oz
Weight of Packaging &
Product
0.85 kg / 30 oz +/- 0.5 oz
Form Factor
Half-length, dual width Graphics Card
ENVIRONMENTAL
Ambient Operating Temp
0°C to 40°C / 32°F to 104°F
Storage Temp
-20°C to 60°C / -4°F to 140°F
Humidity
20 to 90% non-condensing
Ethernet
HDBaseT
Tuesday, May 14, 2019 V1.3 - Copyright 2019, advoli Limited. All Rights Reserved.
