ADVANTEST R3765AG Operation Manual Download Page 27 | Manualshive

Page: 27 / 446

background image

R3765/67G Series Network Analyzer Operation Manual

1.5 Supply Description

1-7

1.5

Supply Description

1.5.1

Power Supply Specifications

WARNING!
Safety use the R3765/67G series according to the power requirement.
The R3765/67G series might be damaged in the case not following the power requirement.

The power requirement of the R3765/67G series is shown in the following.
Use the power supply by which the power requirement of the R3765/67G series is satisfied.

*The supply voltage of the R3765/67G series is automatically changed over (100/240V).

1.5.2

Replacing the Power Fuse

WARNING!
1. Before replacing the power fuse, be sure to turn the power switch OFF and remove the power

cable from the outlet.

2. For continued protection against fire hazard, use a fuse of the type and rating which match the

supply voltage.

Power fuse is located in the power connector on the rear panel.
To check or replace the power fuse as follows.

100V

AC

operation

220V

AC

operation

Input voltage range

90V - 132V

198V - 250V

Frequency range

48Hz - 66Hz

Power fuse

T6.3A/250V

Power consumption

250VA or below

To restore the fuse after

confirmed or exchanged.

To take out the fuse in the power

connector at the rear panel.

Standard of fuse
T6.3A/250V

Draw it out by using
the minus diriver.

«
...
25
26
27
28
29
...
»

Summary of Contents for R3765AG































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for R3765AG

Brand: 3M Pages: 2

Brand: 3M Pages: 16

Brand: Camille Bauer Pages: 12

Brand: Cecomp Pages: 4

Brand: PCB Piezotronics Pages: 16

fieldscout TDR 100

Brand: Spectrum Techniques Pages: 20

Brand: Kipp & Zonen Pages: 32

Brand: Parker Pages: 16

Brand: Waterproof Pages: 51

Brand: WAGNER Pages: 4

Micropilot S FMR 53 Series

Brand: E+H Pages: 12

Brand: SmarTire Pages: 14

Brand: bihl+Wiedemann Pages: 16

Brand: F&J Pages: 33

Brand: MRC Pages: 35

FOTOMETER 2008 COOL

Brand: id LAB Pages: 8

Brand: IMT Analytics Pages: 46

Brand: Bartec Auto ID Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands