Advantek Networks AWR-MIMO-54RA Page 9 User Manual Download

Page: 9 / 58

Button/port Description

Reset

Reset configurations to default. Press the button and hold for 10 seconds.

LAN

(1x, 2x, 3x, 4x)

Connect LAN systems with RJ-45 cable.

WAN

Connect DSL or Cable modem.

PWR

Connect with Power Adapter.

1.5 Installation Instruction

1) Power off Wireless Router and DSL/cable modem.

2) Connect systems to the LAN ports on the Wireless Router with straight LAN cables.

3) Connect the DSL or cable modem to the WAN port on the Wireless Router.

4) Power on DSL or cable modem first, then connect power adapter to the power jack

on the rear panel of Wireless Router and plug the power cable into an outlet.

5) Check LEDs.

a) Once power on Wireless Router, Power LED should be on.

b) LAN LED should be on for each active LAN connection.

c) The WAN LED should be on when the DSL or cable modem is connected.

Warning:

Only use the power adapter is provided from this package, use other power adapter

may cause hardware damage

Summary of Contents for AWR-MIMO-54RA



























































Search results

Summary of Contents for AWR-MIMO-54RA

Reviews:

Related manuals for AWR-MIMO-54RA

Brands by name

Popular brands

Advantek Networks AWR-MIMO-54RA, User Manual

Search results

Summary of Contents for AWR-MIMO-54RA

Reviews:

Related manuals for AWR-MIMO-54RA

Brands by name

Popular brands