Advantech WISE-1540 User Manual Download Page 2

WISE-1540 User Manual 

Copyright 

The documentation and the software included with this product are copyrighted 2016 

by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right 

to make improvements in the products described in this manual at any time without 

notice. No part of this manual may be reproduced, copied, translated or transmitted 

in any form or by any means without the prior written permission of Advantech Co., 

Ltd. Information provided in this manual is intended to be accurate and reliable. However, 

Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements 

of the rights of third parties, which may result from its use. 

Acknowledgements 

ARM is trademarks of ARM Corporation. 

Freescale is trademarks of Freescale Corporation. 

Microsoft Windows are registered trademarks of Microsoft Corp. 

All other product names or trademarks are properties of their respective owners. 

Product Warranty (2 years) 

Advantech warrants to you, the original purchaser, that each of its products will be 

free from defects in materials and workmanship for two years from the date of purchase. 

This warranty does not apply to any products which have been repaired or altered by 

persons other than repair personnel authorized by Advantech, or which have been 

subject to misuse, abuse, accident or improper installation. Advantech assumes no 

liability under the terms of this warranty as a consequence of such events. 

Because of Advantech’s high quality-control standards and rigorous testing, most of 

our customers never need to use our repair service. If an Advantech product is defective, 

it will be repaired or replaced at no charge during the warranty period. For out-of- 

warranty repairs, you will be billed according to the cost of replacement materials, 

service time and freight. Please consult your dealer for more details. 

If you think you have a defective product, follow these steps: 

1. 

Collect all the information about the problem encountered. (For example, CPU speed, 

Advantech products used, other hardware and software used, etc.) Note anything 

abnormal and list any onscreen messages you get when the problem occurs. 

2. 

Call your dealer and describe the problem. Please have your manual, product, and any 

helpful information readily available. 

3. 

If your product is diagnosed as defective, obtain an RMA (return merchandize 

authorization) number from your dealer. This allows us to process your return more 

quickly. 

4. 

Carefully pack the defective product, a fully-completed Repair and Replacement Order 

Card and a photocopy proof of purchase date (such as your sales receipt) in a 

Summary of Contents for WISE-1540












































Reviews: