Advantech UNO-2362G Series User Manual Download Page 6

UNO-2362G User Manual

vi

Safety Instructions

1.

Read these safety instructions carefully.

2.

Keep this User Manual for later reference.

3.

Disconnect this equipment from any AC outlet before cleaning. Use a damp 

cloth. Do not use liquid or spray detergents for cleaning.

4.

For plug-in equipment, the power outlet socket must be located near the equip

-

ment and must be easily accessible.

5.

Keep this equipment away from humidity.

6.

Put this equipment on a reliable surface during installation. Dropping it or letting 

it fall may cause damage.

7.

The openings on the enclosure are for air convection. Protect the equipment 

from overheating. DO NOT COVER THE OPENINGS.

8.

Make sure the voltage of the power source is correct before connecting the 

equipment to the power outlet.

9.

Position the power cord so that people cannot step on it. Do not place anything 

over the power cord.

10.

All cautions and warnings on the equipment should be noted.

11.

If the equipment is not used for a long time, disconnect it from the power source 

to avoid damage by transient over-voltage.

12.

Never pour any liquid into an opening. This may cause fire or electrical shock.

13.

Never open the equipment. For safety reasons, the equipment should be 

opened only by qualified service personnel.

14.

If one of the following situations arises, get the equipment checked by service 

personnel:

The power cord or plug is damaged.

Liquid has penetrated into the equipment.

The equipment has been exposed to moisture.

The equipment does not work well, or you cannot get it to work according to 

the user's manual.

The equipment has been dropped and damaged.

The equipment has obvious signs of breakage.

15.

DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE 

STORAGE TEMPERATURE MAY GO BELOW -10 °C (-14 °F) OR ABOVE 60 

°C (140 °F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT 

SHOULD BE IN A CONTROLLED ENVIRONMENT.

16.

CAUTION

: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY 

REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE 

RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES 

ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.

ATTENTION

: Danger d'explosion si la batterie est mal REMPLACE. REM

-

PLACER UNIQUEMENT PAR LE MEME TYPE OU EQUIVALENT RECOM

-

MANDÉ PAR LE FABRICANT, jeter les piles usagées SELON LES 

INSTRUCTIONS DU FABRICANT.

17.

The sound pressure level at the operator's position according to IEC 704-1:1982 

is no more than 70 dB (A).

DISCLAIMER: This set of instructions  is given according to IEC 704-1. Advantech

disclaims all responsibility for the accuracy of any statements contained herein.

Summary of Contents for UNO-2362G Series







































Reviews: