manualshive.com logo in svg

Advantech PPC-L158T, User Manual, Page: 54 / 59

Share
Download
Advantech PPC-L158T User Manual Download Page 54

PPC-L158T User Manual

44

6.1

Introduction

A Driver CD is supplied inside the accessory box. Customers may need to use an
external USB CD-ROM related device to load the CD and install the drivers for the
PPC-L158T.

6.1.1 Driver Installation

Before installing the Ethernet driver, note the procedures below. It is necessary to
know which operating system is installed on the PPC-L158T. Then refer to the corre-
sponding installation flow chart. Follow the steps described in the flow chart to com-
plete the installation quickly. There are Drivers and documents included on the CD for
the chipset, LAN, Audio, Touchscreen, VGA, and USB, as well as a PDF copy of this
user manual.

6.2

Updating Driver Search on the Advantech 
Website

For further information about installing drivers on the PPC-L158T, and to access
driver updates, troubleshooting guides and FAQ lists, visit the following web
resources:

Advantech websites:

www.advantech.com

www.advantech.com.tw

Note!

1.

The CD-ROM drive is designated as "D" throughout this chapter.

2.

<Enter> means pressing the "Enter" key on the keyboard.

Summary of Contents for PPC-L158T




























































Reviews:

No comments