Advantech PPC-3150SW-PN4A User Manual Download Page 4

PPC-3150SW_3180SW User Manual

iv

Safety Instructions

1.

Read these safety instructions carefully.

2.

Retain this user manual for future reference.

3.

Disconnect the equipment from any power outlet before cleaning. Use only a 
damp cloth for cleaning. Do not use liquid or spray detergents.

4.

For pluggable equipment, the power outlet socket must be located near the 
equipment and easily accessible.

5.

Protect the equipment from humidity.

6.

Place the equipment on a reliable surface during installation. Dropping or letting 
the equipment fall may cause damage.

7.

The openings on the enclosure are for air convection. Protect the equipment 
from overheating. Do not cover the openings.

8.

Ensure that the voltage of the power source is correct before connecting the 
equipment to a power outlet.

9.

Position the power cord away from high-traffic areas. Do not place anything over 
the power cord.

10.

All cautions and warnings on the equipment should be noted.

11.

If the equipment is not used for a long time, disconnect it from the power source 
to avoid damage from transient overvoltage.

12.

Never pour any liquid into an opening. This may cause fire or electrical shock.

13.

Never open the equipment. For safety reasons, the equipment should be 
opened only by qualified service personnel.

14.

If one of the following occurs, have the equipment checked by service person-
nel:



The power cord or plug is damaged.



Liquid has penetrated the equipment.



The equipment has been exposed to moisture.



The equipment is malfunctioning, or does not operate according to the user 

manual.



The equipment has been dropped and damaged.



The equipment shows obvious signs of breakage.

15.

Do not leave the equipment in an environment with a storage temperature of 
below -40 °C (-40 °F) or above 85 °C (185 °F) as this may cause damage to the 
components. The equipment should be stored in a controlled environment.

16.

CAUTION: Batteries are at risk of exploding if incorrectly replaced. Replace only 
with the same or equivalent type as recommended by the manufacturer. Discard 
used batteries according to the manufacturer's instructions.

          ATTENTION: Il y a danger d'explosion s'il y a remplacement incorrect de la pile.   
        Remplacer uniquement avec une pile du même type ou d'un type équivalent
        recommandé par le constructeur.

17.

In accordance with IEC 704-1:1982 specifications, the sound pressure level at 
the operator's position does not exceed 70 dB (A).

18.

DISCLAIMER: These instructions are provided according to IEC 704-1 stan-
dards. Advantech disclaims all responsibility for the accuracy of any statements 
contained herein.

19.

This product is intended to be supplied by an UL-certified power supply or DC 
power source suitable for use at TMA: 50 °C minimum (with an SSD) or TMA: 
40 °C minimum (with an HDD), and whose output meets ES1 and is rated 12 ~ 
24 V

DC

 with 5 ~ 2.5A minimum (60W minimum). Please contact Advantech for 

further information.

Summary of Contents for PPC-3150SW-PN4A





















































Reviews: