![Advantech PCM-9581 User Manual Download Page 29](http://html1.mh-extra.com/html/advantech/pcm-9581/pcm-9581_user-manual_2857939029.webp)
19
Chapter 2
2.9 Floppy drive connector (CN8)
You can attach up to two floppy drives to the PCM-9581’s on-board con-
troller. This is useful for notebooks with 26 pin slim-FDD cable (part
no:1906000001), for example.
You can use any combination of 5.25”(360 KB and 1.2MB) and/or
3.5”(720 KB, 1.44MB, and 2.88 MB) drives. A 26 pin slim-FDD cable,
26-34pin daisy-chain drive cable converter, and appropriate 34 pin flat
cable are required.
2.9.1 Connecting the floppy drive
1.
Plug the 26-pin slim FDD-cable connector into CN8 of PCM-9581
board and the 26-34pin daisy-chain drive cable converter. Make
sure that the red wire corresponds to pin one on the connector.
2.
Plug the 34-pin flat-cable connector into 26-34pin daisy-chain
drive cable connector. Make sure that the red-wire corresponds to
pin one on the connector.
3.
Attach the appropriate connector at the end of the cable to the
floppy drive(s). You can use only one connector in the set. The set
on the end (after the twist in the cable) connects to A: drive. The set
in the middle connects to the B: drive.
4.
If you are connecting a 5.25” floppy drive, line up the slot in the
PCB (printed circuit board) with the blocked-off part of the cable
connector.
If you are connecting a 3.5” floppy drive, you may have trouble deter-
mining which pin is number one. Look for a number printed on the circuit
board indicating pin number one. In addition, the connector on the floppy
drive may have a slot. When the slot is up, pin number one should be on
the right. Check the documentation that came with the drive for more
information.
If you desire, connect the B: drive to the connectors in the middle of the
cable as described above.
In case you need to make your own cable, you can find the pin assign-
ments for the board’s connector in Appendix C.
Summary of Contents for PCM-9581
