PCI-6873 Startup Manual
Specifications
Solid State Disk
Solid State Disk (SSD):
Supports CompactFlash Card
Type I/II, CFC card shares IDE channel and occupies IDE
master
Caution! If CF card is used as IDE master, please use 40-
pin IDE cable (Advantech’s P/N: 1701400607) to
connect another IDE device as IDE slave.
VGA/LCDS Interface
Chipset:
AMD Geode LX800
Memory Size:
Optimized Shared Memory Architecture,
supports 64MB frame buffer using system memory
Resolution:
CRT resolution: up to 1600 x 1200 x 16 bpp
at 100 Hz
TTL interface:
Supports 24 bit TTL, resolution up to 1600
x 1200 x 32 bpp at 60 Hz for TFT LCD
LVDS Interface:
Supports single channel 18-bit LVDS, by
Hirose DF13, 20 pin connector
Dual Simultaneous Display:
CRT + TTL LCD, CRT +
LVDS
Note: LVDS and TTL cannot be used at the same time.
Ethernet Interface
Chipset supports:
10/100Mbps Realtek RTL8100
Interface:
1 x RJ-45 connector
Connector:
One RJ-45 connector
Standard IEEE 802.3u (100 Mbps) protocol compatible
Built-in boot ROM (RTL8100)
OS Support
This board supports Win XP, Win CE and Win XPe
For further information about OS support on your
PCI-6873, visit the following Advantech web resource
http://www.advantech.com or please contact technical
support center.
Mechanical and Environmental
Dimensions:
185 x 122 mm (7.3” x 4.8”)
Power Supply Type:
AT/ATX
Power Requirement:
+5 V ± 5%, +12 V ± 5% (Optional),
+5 V standby for ATX mode or support 5 V power
only (If using 5 V only power, LVDS can’t work due to no
12 V power supply)
Power Consumption: (Geode LX800, 256 MB DDR333)
- Max: +5 V @ 1.64 A, +12 V @ 0.07 A
- Typical: +5 V @ 1.42 A, +12 V @ 0.07 A
Operating temperature:
0 ~ 60° C (32 ~ 140° F)
Operating Humidity: 1
0% ~ 90% relative humidity,
non-condensing
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
The board has a number of jumpers that allow you to
configure your system to suit your application.
The table below lists the functions of the jumpers and
connectors.
Jumpers
Label
Function
CN8
CMOS Setting
CN14
LVDS Power select
CN19
232/422/485 SEL
CN34
AT/ATX Selector
Connectors
Label
Function
CN1
Front Panel
(HDD LED/Reset/suspend/Power Button)
CN2
Printer Port Connector
CN3
Floppy Connector
CN4
IDE
CN5
Inverter Power
CN6
SATA connector
CN7
SATA connector
CN9
USB 0,1
CN10
USB 2,3
CN11
TFT LCD connector (TTL)
CN12
LVDS
CN13
LAN2 connector (Customization)
CN15
ATX power connector
CN16
VGA
CN17
GPIO
CN18
LAN1 RJ45 connector
CN20
COM3/COM4 connector
CN21
COM1
CN22
COM2
CN23
AC97 connector
CN24
System FAN connector (optional)
CN25
Audio Connector (Customization)
CN26
ATX suspend power connector
CN27
Audio Connector; left out & Center out
(Customization)
Jumpers and Connectors
