background image

19

Appendix B  

Optical

•  

Visible light transmission:

 75% typical (>74% @ 550 nm test)

•  

Clarity: 

Clear Finish - 25%, Antiglare Finish - 15%

Sensor  board

•  Chemical strengthened glass with 4 H hardness standard.

(Test condition: ASTM D3363-92A)

Ball  drop  test

•  Able to bear a 225 g steel ball dropped from 660 mm elevation without 

breaking

Environmental Specifications

•  

Operating Temperature Range:

 -20°  C ~ +50° C, 2 weeks at 50° C / 

90% RH.

•  

Storage Temperature High:

 +70° C, 240 hours at ambient humidity.

•  

Storage Temperature Low:

 -40° C, continuous at ambient humidity.

•  

Accelerated Aging:

 100 hours at 60° C / 95% RH.

•  

Thermal Shock:

 25 cycles (one cycle is 30 min. dwell alternating from 

-40 to +85° C with less than 10 min. transfer time.

B.3  Installing Driver for Windows 2000/XP

The touchscreen has drivers for Windows 2000 and Windows XP. You 
should read the instructions in this chapter carefully before you attempt 
installation. 

Note 1: 

The following windows illustrations are examples 
only. You must follow the flow chart instructions 
and pay attention to the instructions which then 
appear on your screen.

Note 2:

Install the HMI CD Driver into the system 
CD-ROM (D:\ means CD-ROM)

Summary of Contents for FPM-3100H Series















































Reviews: