manualshive.com logo in svg

Advantech ES-3112 G, User Manual

Share
Download
Advantech ES-3112 G User Manual Download Page 12

ES-3112 Users Manual

6

1.5  Touchscreen Specifications

1.5.1 ES-3112C-XA (Capacity)

•  

Type:

 3M Touch Systems-Microtouch capacity touch screen

•  

Resolution:

 1024 x 1024

•  

Light Transmission:

 85%

•  

Touch Life Cycle:

 225 million

•  

Controller:

 RS-232 interface

•  

Communication speed:

 up to 19.2K baud.

•  

Power consumption:

 +5 V @ 100 mA

1.5.2 ES-3112R-XA (Resistive)

•  

Type:

 EloTouch resistive touch screen

•  Resolution: Continuous
•  Light Transmission: 75%
•  Touch Life Cycle: 35 million
•  

Controller:

 RS-232 interface

•  Communication speed: up to 19.2K baud.
•  Power consumption: +5 V @ 200 mA

1.5.3 ES-3112S-XA (SAW)

•  

Type: 

EloTouch Surface Acoustic Wave (SAW)

•  Resolution: 4096 x 4096
•  Light Transmission: 91%
•  Touch Life Cycle: 50 millions
•  

Controller:

 RS-232 interface

•  Communication speed: up to 19.2K baud.
•  Power consumption: +5 V @ 60 mA

Summary of Contents for ES-3112 G



































Reviews:

No comments

Brands by name

Popular brands

Load more brands